Unlike fence feedback, commands to update timeline semaphore feedback
slots can't be fully pre-recorded because of the counter value input
for signaling timeline semaphores. To avoid fully recording commands
during vkQueueSubmit, pre-record commands that write a counter value
from a feedback "src" slot to the feedback "dst" slot. Then at
vkQueueSubmit, parse the signal semaphores and write the signal counter
value in the feedback src slot and append the command that writes from
that feedback src slot offset to the command buffer associated with the
signal semaphore.
Signed-off-by: Juston Li <justonli@google.com>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/20500>
Refactor into the following stages:
- prepare: Does an initial pass setting vn_queue_submission fields
and fixing up semaphores.
- alloc_storage: based on fields (including counts) from prepare,
calculate and allocate the amount of temporary storage needed.
- setup_batches: perform any modifications on the submission
batches using the allocated temporary storage.
- cleanup: free any temporary storage used.
Currently, only fence feedback needs alloc_storage and setup_batches
to append fence feedback to the submission but this slow will also
be utilized by upcoming timeline semaphore feedback.
Signed-off-by: Juston Li <justonli@google.com>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/20500>
This hardware bug is the result of a control flow optimization present
in Gfx8-9 meant to prevent the ELSE instruction from disabling all
channels and update the control flow stack only to have them
re-enabled at the ENDIF instruction executed immediately after it.
Instead, on Gfx8-9 an ELSE instruction that would normally have ended
up with all channels disabled would pop off the last element of the
stack and jump directly to JIP+1 instead of to the ENDIF at JIP,
skipping over the ENDIF instruction. In simple cases this would work
okay (though it's actual performance benefit is questionable), but in
cases where a branch instruction within the IF block (e.g. BREAK or
CONTINUE) caused all active channels to jump outside the IF
conditional, the optimization would break the JIP chain of "join"
instructions by skipping the ENDIF, causing the block of instructions
immediately after the ENDIF to execute with all channels disabled
until execution reaches the reconvergence point.
This issue was observed on SKL in the
dEQP-VK.reconvergence.subgroup_uniform_control_flow_elect.compute.nesting4.0.38
test in combination with some Vulkan binding model changes Lionel is
working on. In such cases the execution with all channels disabled
was leading to corruption of an indirect message descriptor, causing a
hang.
Unfortunately the hardware bug doesn't provide a recommended
workaround. In order to fix the problem we point the JIP of an ELSE
instruction to the instruction immediately before the ENDIF -- However
that's not expected to work due to the restriction that JIP and UIP
must be equal if and only if BranchCtrl is disabled -- So this patch
also enables BranchCtrl, which is intended to support join
instructions within the "ELSE" block, which in turn disables the
optimization described above, which in turn causes us to execute the
instruction immediately *before* the ENDIF with all channels disabled
-- So in order to avoid further fallout from executing code with all
channels disabled we need to insert a NOP before ENDIF instructions
that have a matching ELSE instruction.
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/20921>
It took me a minute to figure out why the last uni_offsets NULL check
didn't also need to check num_offsets. I think this makes the code
slightly easier to understand.
Reviewed-By: Mike Blumenkrantz <michael.blumenkrantz@gmail.com>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/21144>
A few lines earlier uni_offsets is accessed with ubo scaled by
PIPE_MAX_CONSTANT_BUFFERS:
if (uni_offsets[ubo * PIPE_MAX_CONSTANT_BUFFERS + i] == offset)
Found by inspection.
Looking at the before and after NIR code for
dEQP-VK.graphicsfuzz.cov-int-initialize-from-multiple-large-arrays,
using the correct indexing appears to enable the pass to inline an
additional uniform. My guess is that when a uniform is used more than
once, the first loop wouldn't find the offset recored in the table
because it was recorded at the wrong location.
Fixes: d23a9380dd ("lavapipe: implement extreme uniform inlining")
Reviewed-By: Mike Blumenkrantz <michael.blumenkrantz@gmail.com>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/21144>
Revert part of the commit 8187b35f to disable decoder fence for now
since it is causing regression for transcoding tests.
Signed-off-by: Boyuan Zhang <boyuan.zhang@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Daniel Almeida <daniel.almeida@collabora.com>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/21145>
Point sprite coordinates in general need to be inverted,
not just the texcoords converted to point sprite.
Move point coord y inversion out to its own pass.
Fixes GTF-GL46.gtf21.GL2FixedTests.point_sprites.point_sprites
with FBO dEQP surface.
cc: mesa-stable
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/21050>
Setting default expected values as default in the xml.
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/21105>
Currently, we postpone binning syncs until we record draw calls
and can validate if any of them require accessing protected
resources in the binning stage, however, if the draw calls are
recorded in a secondary command buffer and the barriers have
been recorded in the primary command buffer, we won't apply the
binning sync in the secondary when we record the draw calls
and so we must apply it when we execute the secondary in the
primary.
Fixes flakyness in:
dEQP-VK.api.command_buffers.record_many_draws_secondary_2
cc: mesa-stable
Reviewed-by: Alejandro Piñeiro <apinheiro@igalia.com>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/21162>
The CLE parser in the sim will read this many bytes for each instruction
in a CL, so we should ensure we have at least that many bytes available
in the BO when reading the last instruction, otherwise we can trigger
a GMP violation. It is not clear whether this behavior applies to real
hardware too.
cc: mesa-stable
Reviewed-by: Alejandro Piñeiro <apinheiro@igalia.com>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/21162>
These are ignored by the pvrsrvkm KMD and don't exist in the new KMD.
Signed-off-by: Frank Binns <frank.binns@imgtec.com>
Reviewed-by: Luigi santivetti <luigi.santivetti@imgtec.com>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/21132>
Fixes: 46b099e3
("meson: Ignore unused variables in release builds")
46b099e3 has some issues:
- it doesn't enable unused variables warning on release builds
with assertions enabled;
- it doesn't disable unused variables warning on debug builds
with assertions disabled;
- it doesn't disable unused variables warning when building
with MSVC and assertions are disabled regardless of buildtype,
see #8147. 3/4 regressions reported there have this limitation
alone as root cause.
Reviewed-by: Emma Anholt <emma@anholt.net>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/21154>
On integrated products this makes almost no difference but on discrete
it's pretty important.
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Ivan Briano <ivan.briano@intel.com>
Tested-by: Chuansheng Liu <chuansheng.liu@intel.com>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/21131>
navi21 can do separate image support, using tier 2 DPB messages.
This enables support for doing that in the vulkan video driver.
Reviewed-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/20388>
This adds support for H264 decode on VCN hardware.
It uses the full DPB method, and relies on the application
to allocate an arrayed texture for the DPB to be stored into.
RADV_PERFTEST=video_decode is required to enable this.
Reviewed-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/20388>
The video buffers need to have objects aligned at certain ranges,
this enhances the uploader to allow an alignment to be specified.
Reviewed-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/20388>
The decoder context needs to know what engine it's associated with.
Nowadays, we have render, compute, blitter, even video engines being
used from the same driver. Rather than trying to have a single decoder
and thwacking the engine field back and forth between calls, we make
one per queue family, and stash a pointer in anv_queue for easy access.
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/21149>
In general we should only call it once, and then we should avoid to
call any lowering that introduce back copies. So far we were tracking
that manually out of the nir shader on several places.
Ideally we would like to add a nir_validate rule, but right now there
are some exceptions to this rule. For example right now the Intel
compiler calls nir_lower_io_to_temporaries as part of linking
tess_ctrl/mesh/task sahders.
One option would be to allow drivers to reset the value, but for now
let's not add that validation rule.
Reviewed-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/19338>
LLVMContextSetOpaquePointers() was a temporary workaround offered to
allow transitioning to opaque pointers. Mesa is ready for this now with
recent versions of LLVM (16+). Therefore we limit the workaround of
using LLVMContextSetOpaquePointers() to LLVM 15 now, that this C
interface was removed in LLVM 17.
Reference: 1270879376
Suggested-by: Dave Airlie <airlied@redhat.com>
Closes: https://gitlab.freedesktop.org/mesa/mesa/-/issues/8183
Reviewed-by: Roland Scheidegger <sroland@vmware.com>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/21124>
This will be useful for RADV since it hashes the state.
v3dv changes:
Reviewed-by: Alejandro Piñeiro <apinheiro@igalia.com>
Reviewed-by: Samuel Pitoiset <samuel.pitoiset@gmail.com>
Part-of: <https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/20731>
