The goal is to enable testing of parts of drivers without depending on any
particular kernel version or hardware being present.
Simply set LD_PRELOAD=$PREFIX/lib/libv3d_drm_shim.so in your environment,
and we'll fake a /dev/dri/renderD128 (or whatever the next available node
is) using v3dv3. That node can then be used with the surfaceless or gbm
EGL platforms.
Acked-by: Iago Toral Quiroga <itoral@igalia.com>
If we detect that a scheduling candidate will stall because having a
register source that is the written by the SFU unit in the previous
instruction we reduce its priority so any non stalling operation would
be chosen.
The latency of SFU operations is defined as 2. So they would be scheduled
earlier if other candidates have the same priority.
Finally we won't merge instructions that stall to a previously chosen one.
As the result of the previous one would be waiting for an extra cycle.
Although shader-db result show that instruction are hurt with an increase
of 0.35% the sum of instructions + stalls is reduced a 0.52%. And
the total of sfu-stalls is reduced a 63.51%. It implies also a small
increase in the max-temps metric because of scheduling earlier SFU
operations.
total instructions in shared programs: 9102719 -> 9117851 (0.17%)
instructions in affected programs: 4324628 -> 4339760 (0.35%)
helped: 4162
HURT: 12128
helped stats (abs) min: 1 max: 10 x̄: 1.28 x̃: 1
helped stats (rel) min: 0.09% max: 4.76% x̄: 0.66% x̃: 0.51%
HURT stats (abs) min: 1 max: 27 x̄: 1.69 x̃: 1
HURT stats (rel) min: 0.05% max: 7.69% x̄: 0.87% x̃: 0.68%
95% mean confidence interval for instructions value: 0.90 0.96
95% mean confidence interval for instructions %-change: 0.47% 0.50%
Instructions are HURT.
total max-temps in shared programs: 1327728 -> 1327812 (<.01%)
max-temps in affected programs: 4730 -> 4814 (1.78%)
helped: 61
HURT: 134
helped stats (abs) min: 1 max: 2 x̄: 1.08 x̃: 1
helped stats (rel) min: 2.70% max: 13.33% x̄: 4.89% x̃: 4.17%
HURT stats (abs) min: 1 max: 3 x̄: 1.12 x̃: 1
HURT stats (rel) min: 1.54% max: 20.00% x̄: 6.10% x̃: 5.26%
95% mean confidence interval for max-temps value: 0.28 0.58
95% mean confidence interval for max-temps %-change: 1.80% 3.52%
Max-temps are HURT.
total sfu-stalls in shared programs: 99551 -> 36324 (-63.51%)
sfu-stalls in affected programs: 95029 -> 31802 (-66.53%)
helped: 25882
HURT: 0
helped stats (abs) min: 1 max: 27 x̄: 2.44 x̃: 2
helped stats (rel) min: 5.26% max: 100.00% x̄: 79.86% x̃: 100.00%
95% mean confidence interval for sfu-stalls value: -2.47 -2.42
95% mean confidence interval for sfu-stalls %-change: -80.18% -79.54%
Sfu-stalls are helped.
total inst-and-stalls in shared programs: 9202270 -> 9154175 (-0.52%)
inst-and-stalls in affected programs: 5618516 -> 5570421 (-0.86%)
helped: 22728
HURT: 855
helped stats (abs) min: 1 max: 31 x̄: 2.16 x̃: 1
helped stats (rel) min: 0.07% max: 16.67% x̄: 1.14% x̃: 0.92%
HURT stats (abs) min: 1 max: 5 x̄: 1.25 x̃: 1
HURT stats (rel) min: 0.12% max: 5.26% x̄: 1.24% x̃: 0.86%
95% mean confidence interval for inst-and-stalls value: -2.07 -2.01
95% mean confidence interval for inst-and-stalls %-change: -1.07% -1.05%
Inst-and-stalls are helped.
v2: Rename v3d_qpu_generates_sfu_stalls to v3d_qpu_instr_is_sfu (Eric)
Reviewed-by: Eric Anholt <eric@anholt.net>
SFU operations have a latency of 2 cicles, so if their results
are used in the following cycle to a SFU instruction, the GPU
stalls for an extra cycle until the result is available.
This adds the number of stalls to the shader-db debug mode and
sum of instruction + stalls to evaluate optimizations to schedule
instructions that avoid generating sfu-stalls.
v2: Rename v3d_qpu_generates_sfu_stalls to v3d_qpu_instr_is_sfu (Eric)
Reviewed-by: Eric Anholt <eric@anholt.net>
nir_lower_io leaves around deref_var instructions after lowering away
deref intrinsics. This ends up breaking validation after v3d_nir_lower_io
removes variables not actually being stored by the shader's
store_output()s.
Reviewed-by: Iago Toral Quiroga <itoral@igalia.com>
We want to split the tlb specifier setup from the color writes, because when
we implement per-sample color writes we want to do the latter for all the
samples, but the former only once.
Reviewed-by: Eric Anholt <eric@anholt.net>
We will soon be adding per-sample color writes which means additional
complexity and more indentation (we will need another loop to emit
the writes for each individual sample), so this will help keeping
things simple and a bit more readable.
Reviewed-by: Eric Anholt <eric@anholt.net>
This allows to remove a mov of 1/-1, as it is implicit with the
operation.
As with atomic inc/dec/add, usual shader-db set doesn't include any
GLES shader using it. So using as workaround vk-gl-cts shaders, we get
this:
total instructions in shared programs: 1217013 -> 1217006 (<.01%)
instructions in affected programs: 53 -> 46 (-13.21%)
helped: 2
HURT: 0
One of the helped shader went from 40 to 34 instructions.
Reviewed-by: Eric Anholt <eric@anholt.net>
And moved to new auxiliar method v3d40_image_load_store_tmu_op,
equivalent to the nir_to_nir v3d_general_tmu_op, to clean-up a little.
Reviewed-by: Eric Anholt <eric@anholt.net>
Among other things, this avoid the need of loading 1/-1 constants (so
one less operation).
The removed comment suggest the option of adding support on NIR for
inc/dec. Intel just uses an auxiliar method to get which hw operation
is needed, so no lowering is needed. And at the same time, being so
small, seems unreasonable to try to add a general one on NIR
itself. It is more easy to just adapt the method here (that is what
the patch does right now).
It is worth to note that we are not getting any change on shader-db
stats because all those methods are used on the usual shader-db set
with shaders needing GLSL > 4.2. In general there aren't too many GLSL
ES 3.1 tests.
As an alternative, we captured the GLES3/GLSL31/GLS32 used on
vk-gl-cts, even if that is not a real life usage of shaders. With
those we get the following:
total instructions in shared programs: 1217022 -> 1217013 (<.01%)
instructions in affected programs: 117 -> 108 (-7.69%)
helped: 6
HURT: 0
helped stats (abs) min: 1 max: 2 x̄: 1.50 x̃: 1
helped stats (rel) min: 3.57% max: 10.00% x̄: 8.09% x̃: 9.09%
95% mean confidence interval for instructions value: -2.07 -0.93
95% mean confidence interval for instructions %-change: -10.54% -5.64%
Instructions are helped.
Note that the shaders helped are really low because most of the
vk-gl-cts tests using AtomicInc/Dec/Add are mostly used on compute
shaders. Although right now there is a branch around with CS support,
the usual is doing the stats against master.
Reviewed-by: Eric Anholt <eric@anholt.net>
They are already defined, although is a slightly different format on
the generated packet headers, so it was needed to change how it is
used on nir_to_vir.
In addition to allow to remove some duplicated headers, it will allow
to define just one get_op_for_atomic_add aux method later to support
using inc/dec instead of add of 1/-1.
Reviewed-by: Eric Anholt <eric@anholt.net>
This implements support for OpenGL logic operations by emitting code to read
from the TLB if needed and blending the fragment output accordingly. It is
similar to VC4's blend lowering pass, but exclusive to logic operations, since
blending is otherwise supported in hardware.
The pass doesn't handle MSAA targets yet.
Fixes the following piglit tests:
spec/!opengl 1.0/gl-1.0-logicop/*
spec/!opengl 1.1/gl-1.1-xor
spec/!opengl 1.1/gl-1.1-xor-copypixels
It also fixes text cursor rendering in Libreoffice with the GTK+2 theme, which
is rendered via glamor using the XOR logic operation.
v2: fix checks for allowed variable location and maximum render target (Eric)
Reviewed-by: Eric Anholt <eric@anholt.net>
Until now we have always been emitting our scoreboard locks on the last thread
switch to improve parallelism. We did this by emitting our last thread switch
right before our tlb writes at the very end of the program, where we know that
we are outside control flow.
Unfortunately, this strategy is not valid when we have tlb color reads too, as
these will happen before this point in the program and can happen inside
control flow.
To fix this we always emit a thread switch before the first tlb load and if we
see additional thread switches after that point, we change the strategy to lock
on the first thread switch.
v2: change the solution so it is expected to work in more scenarios (Eric).
Reviewed-by: Eric Anholt <eric@anholt.net>
We will be emitting this intrinsic to signal TLB color loads when we implement
OpenGL logic operations, where we need to blend the fragment shader color
output with the existing color in the render target.
Per-sample TLB reads are not supported yet.
v2: fix the offset into the color_reads array (Eric).
Reviewed-by: Eric Anholt <eric@anholt.net>
We need to scale the size of these arrays to consider up to
V3D_MAX_DRAW_BUFFERS render targets and 4 components per color.
v2: we want to store each color component separately, so scale by 4 too.
Reviewed-by: Eric Anholt <eric@anholt.net>
The ldtlbu version will read an implicit uniform with the TLB read
specifier and should be used for the first read in a sequence
of TLB reads (unless the default configuration is valid, in which
case we can use ldtlb). The ldtlb version is used for any subsequent
TLB read in the sequence.
Reviewed-by: Eric Anholt <eric@anholt.net>
We already have code to print these signals but the early return in the code
that checks if any signals are present present was missing the checks for them,
so it would skip printing them unless they were paired with other signals.
Reviewed-by: Eric Anholt <eric@anholt.net>
That is: the five least significant bits provide the values of
'bits' and 'offset' which is the case for all hardware currently
supported by NIR and using the bfm/bfe instructions.
This patch also changes the lowering of bitfield_insert/extract
using shifts to not use bfm and removes the flag 'lower_bfm'.
Tested-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Connor Abbott <cwabbott0@gmail.com>
Either all channels executed the 'then' block, in which case all
channels will directly jump to the 'endif' block at the end of the
'then' block, or all channels execute the 'else' block (so no
execution masking is necessary).
Shader-db results:
total instructions in shared programs: 9119238 -> 9117550 (-0.02%)
instructions in affected programs: 401252 -> 399564 (-0.42%)
helped: 855
HURT: 77
total uniforms in shared programs: 3022622 -> 3022605 (<.01%)
uniforms in affected programs: 3566 -> 3549 (-0.48%)
helped: 17
HURT: 0
total max-temps in shared programs: 1327762 -> 1327774 (<.01%)
max-temps in affected programs: 619 -> 631 (1.94%)
helped: 2
HURT: 15
Reviewed-by: Eric Anholt <eric@anholt.net>
We were not accountint for small immediates in the B mux so the scheduler
was interpreting these are regular register file accesses, which could
lead to additional (incorrect) write-read dependencies.
Shader-db changes:
total instructions in shared programs: 9163664 -> 9137263 (-0.29%)
instructions in affected programs: 3931035 -> 3904634 (-0.67%)
helped: 12457
HURT: 2563
total max-temps in shared programs: 1325787 -> 1325597 (-0.01%)
max-temps in affected programs: 5746 -> 5556 (-3.31%)
helped: 186
HURT: 16
helped stats (abs) min: 1 max: 4 x̄: 1.12 x̃: 1
helped stats (rel) min: 1.45% max: 22.22% x̄: 4.42% x̃: 3.28%
HURT stats (abs) min: 1 max: 3 x̄: 1.12 x̃: 1
HURT stats (rel) min: 2.86% max: 10.00% x̄: 5.76% x̃: 5.88%
95% mean confidence interval for max-temps value: -1.04 -0.84
95% mean confidence interval for max-temps %-change: -4.16% -3.07%
Max-temps are helped.
Reviewed-by: Eric Anholt <eric@anholt.net>
Currently, st/mesa is always calling the GLSL IR lower_instructions()
pass with MOD_TO_FLOOR set, so mod operations will be lowered before
ever reaching NIR. This enables the same lowering at the NIR level,
which will let me shut off the GLSL IR path for NIR-based drivers.
Reviewed-by: Marek Olšák <marek.olsak@amd.com>
Acked-by: Eric Anholt <eric@anholt.net>
The difference between imov and fmov has been a constant source of
confusion in NIR for years. No one really knows why we have two or when
to use one vs. the other. The real reason is that they do different
things in the presence of source and destination modifiers. However,
without modifiers (which many back-ends don't have), they are identical.
Now that we've reworked nir_lower_to_source_mods to leave one abs/neg
instruction in place rather than replacing them with imov or fmov
instructions, we don't need two different instructions at all anymore.
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>
Reviewed-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Reviewed-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Rob Clark <robdclark@chromium.org>
This can be used by both etnaviv and freedreno/a2xx as they are both vec4
architectures with some instructions being scalar-only.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
I don't know why I thought NIR_PASS always set the progress variable.
Derp.
Fixes: d41cdef2a5 ("nir: Use the flrp lowering pass instead of nir_opt_algebraic")
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Timothy Arceri <tarceri@itsqueeze.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Coverity CID: 1444996
Coverity CID: 1444995
Coverity CID: 1444994
Coverity CID: 1444993
Coverity CID: 1444991
Coverity CID: 1444989
I tried to be very careful while updating all the various drivers, but I
don't have any of that hardware for testing. :(
i965 is the only platform that sets always_precise = true, and it is
only set true for fragment shaders. Gen4 and Gen5 both set lower_flrp32
only for vertex shaders. For fragment shaders, nir_op_flrp is lowered
during code generation as a(1-c)+bc. On all other platforms 64-bit
nir_op_flrp and on Gen11 32-bit nir_op_flrp are lowered using the old
nir_opt_algebraic method.
No changes on any other Intel platforms.
v2: Add panfrost changes.
Iron Lake and GM45 had similar results. (Iron Lake shown)
total cycles in shared programs: 188647754 -> 188647748 (<.01%)
cycles in affected programs: 5096 -> 5090 (-0.12%)
helped: 3
HURT: 0
helped stats (abs) min: 2 max: 2 x̄: 2.00 x̃: 2
helped stats (rel) min: 0.12% max: 0.12% x̄: 0.12% x̃: 0.12%
Reviewed-by: Matt Turner <mattst88@gmail.com>
Driver which do not support native integers should use a lowering
pass to go from integers to floats.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
One special case, `src/util/xmlpool/.gitignore` is not entirely deleted,
as `xmlpool.pot` still gets generated (eg. by `ninja xmlpool-pot`).
Signed-off-by: Eric Engestrom <eric.engestrom@intel.com>
Reviewed-by: Dylan Baker <dylan@pnwbakers.com>
We can't use the QPU functions to detect this until register allocation is
done and we've moved inst->dst into inst->qpu.
Fixes bad TMU sequences from register spilling in
KHR-GLES31.core.compute_shader.shared-max.
Looks like I lost it in a rebase conflict resolution. We'd hit the
unknown intrinsic assertion in
KHR-GLES31.core.compute_shader.shared-struct.
Fixes: 6b1c659825 ("v3d: Add Compute Shader compilation support.")
