Keep track of the number of times a given button or key is pressed on a
device. For regular mouse devices or keyboard devices, such a count will
never exceed 1, but counting button presses could help when button
presses with the same code can originate from different sources. One could
for example implement overlapping tap-drags with button presses by
having them deal with their own life-time independently, sorting out
when the user should receive button presses or not depending on the
pressed count.
Signed-off-by: Jonas Ådahl <jadahl@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
The kernel may send a 'release' event without ever having sent a key
'pressed' event in case the key was pressed before libinput was
initiated. Ignore these events so that we always guarantee a release
event always comes after a pressed event for any given key or button.
Signed-off-by: Jonas Ådahl <jadahl@gmail.com>
It's up to a evdev device backend to configure seat capabilities it
supports. Even though it may be possible for a touchpad to have extra
keys, there is currently no support for sending keyboard events from the
touchpad driver, and if that would be implemented, it'd be a detail of
the touchpad driver, not the generic evdev device part.
Signed-off-by: Jonas Ådahl <jadahl@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
When overriding events of a test device, if one would enable an event
that was already enabled by default for the overridden device, an assert
checking if the event was already enabled would fail and cause the test
to fail.
Since the merging of the default and overriding event lists is implemented
by simply concatinating them letting libevdev deal with ignoring
superfluous event enabling, remove the assert to allow the implementation
to work.
Signed-off-by: Jonas Ådahl <jadahl@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Some tests in test/path.c and test/udev.c are not dependent on
device behaviour but rather managing of device lifetime etc. Run those
tests only once with only one device, resulting more or less the same
code coverage but shorter run time.
Signed-off-by: Jonas Ådahl <jadahl@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
We had reports that the top software button area is hard to hit for those
using the trackpoint and clicking the buttons with their thumb.
Analysis of event recordings (3 different people) for left, right and middle
clicks shows that there is a significant amount of events up to about 10mm
(with outliers up to 12mm) from the top of the touchpad. That maps to 15%.
Interestingly, the middle button is not affected by this, presumably the
haptic feedback of the little dots sticking out from the surface make hitting
the button easier.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Provides the bounding box only, with slot 0 always being the upper/left, slot
1 being the lower-right touch. This needs to use the touch_down etc. litest
interfaces, which are now widened to double (leftover from 489630f58) and a
device-specific private pointer in the litest device.
New device feature for litest: LITEST_SEMI_MT
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
On semi-mt touchpads the reported position of the first finger down may
jump when the pad switches from st to mt mode. When this happens a large
delta gets seen on the first finger at the same time the second fingers
is first seen down, causing a spurious 2 finger scroll event.
Reset the motion history when nfingers changes on semi-mt pads to avoid this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Set BTN_TOUCH, BTN_TOOL_DOUBLETAP automatically depending on the number of
fingers down.
This emulates real event sequences a bit better than the current approach,
though it's not a 100% correct emulation:
1) On real devices, BTN_* are usually sent last before the SYN_REPORT - here
they are sent first to slot in with the custom, device-specific event
sequence. We should only ever look at the complete sequence anyway, so this
shouldn't matter.
2) On real devices, the switch from BTN_TOOL_DOUBLETAP to TRIPLETAP and vice
versa is not always toggled within the same SYN_REPORT
3) On synaptics devices, BTN_TOUCH is released in the frame where
BTN_TOOL_DOUBLETAP is set. It is then immediately set again in the next
frame. With the current litest framework this is hard to integrate, so we
just leave BTN_TOUCH set the whole time, which is what MT devices do if
they don't have BTN_TOOL_DOUBLETAP.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Some tests doesn't use or doesn't need to use the test device
automatically created when adding a test case for certain types of
devices. For these tests, to shorten test run time, don't create the
test devices that would be ignored.
Signed-off-by: Jonas Ådahl <jadahl@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
This is a debugging tool, so the features to debug should be enabled by
default.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
More expressive in the caller and less ambiguous about return values (is it 1?
is it non-zero? can it be negative?)
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Force a cast of the input arguments to a double before the divide, rather
than after the divide.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Multi-touch pads may track less touches then they can report fingers being
present through BTN_TOOL_FOO. So create fake touches for fingers reported
by BTN_TOOL_FOO on multi-touch pads too (when necessary).
This fixes e.g. 3 finger tap not working on the T440s.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Don't process fake touches, e.g. re-adding the same position to the motion
history when they are not dirty. This could trigger for example on a button
press.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
They were already protected against being called twice between SYN_REPORT, but not
for being called twice before a SYN_REPORT arrives.
This allows simplifying tp_process_fake_touch a bit. Note while at it also
also flip the if condition in tp_process_fake_touch so that the if is
true when the finger is down, and remove the bogus t->state = TOUCH_NONE.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
They don't set resolution so we can't calculate the size but we know they're
big enough to need palm detection.
And fix the descriptor for the bcm5974. For some reason this was advertising
synaptics coordinates. Fix it to represent (one of) the apple touchpads.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Add the config status enum to the config doxygen group, and remove a
superfluous argument for an @ingroup command.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
On small touchpads, a touch that intends to go across the width of the
touchpad is likely to start in the edge zone. Likewise, on those touchpads the
chances of a palm event happening on the edge is small.
A minimum width of 8cm determined by an elaborate process of completely
unscientific guesswork: the x220 is roughly 7.5cm across and doesn't suffer
much from edge events, the T440s is 10cm across and definitely suffers from
it. So the trigger width likely somewhere in between which makes 8cm about as
valid as any other guess.
Note that this disables palm detection for resolution-less touchpads too - if
we don't know how big the touchpad is we can't know if palm detection on the
edges is necessary.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Any legitimate finger movement that starts in the palm area is expected to
move out of the palm area at an angle roughly orthogonal to the edge of the
touchpad. Check for the direction of the movement vector, and if it is within
the accepted cardinal/ordinal directions then proceed.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
On small touchpads a touch that is intended to traverse much of the screen
width may start at the very edge, i.e. in the palm zone.
In that case, and if the touch moves out of the palm zone quickly enough, drop
the palm label and make it a normal touchpoint.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
A large part of palm events are situated on the far edges of the touchpad. In
a test run on a T440s while typing a long email all but 2 touch points were
located in the outer ~5% of the touchpad. Define a 5% exclusion zone on the
left and right edges in which new touchpoint is automatically assigned to be a
palm.
A finger may move into that exclusion zone without being marked as palm, it
just can't start in one.
On clickpads, the exclusion zone does not extend into the software buttons.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Makes it possible to use from the touchpad code.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Until uinput gets that capability (likely not before 3.17) all we can do is a
racy approach of setting it after creating it. That won't work well for
anything test where libinput is already listening to udev when the device is
created, but it does work for those cases where libinput is started after the
device was initialized.
And it's a better alternative than not testing anything dependent on
resolution settings.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
This breaks when we have a device resolution set on the test devices,
specificially on the T440. The current tests use a delta of 1% of the device
which with the resolution set results in an effective delta of 3 - above the
scroll threshold.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Using a 0-100% range is useful but in some cases we need events with finer
than 1% granularity.
And fix up the two-finger test that now fails. This was a bug in the test
anyway, the dx/dy supplied here was 1% of the touchpad width. Confined to
integers this meant we only ever had the touch down, then the single move by
1%. That caused two events - not enough to satisfy tp_estimate_delta, so we
always had a delta of 0/0 regardless of the size of the move.
Now with doubles this fails, so drop it to 0.1% instead, which is small enough
on all touchpads we currently have.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
The current touch may not be the pointer touch, so it's pointless checking the
history size on that touch. Instead, search for the pointer touch first, check
if it's dirty and then check the history size.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
In an attempt to bring method into the madness, normalize the touchpad deltas
to those of a USB mouse with 400 dpi. This way the data we're dealing with in
the acceleration code is of a known quantity.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
The resolution-based scaling may result in deltas of 0. The accel code doesn't
handle 0 deltas too well. 0/0 deltas can't happen for EV_REL devices, so the
code just isn't designed for it.
Most notably, events with delta 0/0 have no direction. That messes up the
history-based velocity calculation which stops whenever the current vector's
direction changes from the one in the trackers.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
This just moves a decimal point around, at the expense of making the approach
harder to understand. The only time the const acceleration matters is when
applied to the velocity but it only matters in relation to the threshold which
is a fixed number.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
velocity is in unit/ms, the threshold is in units/ms. Once we divide
velocity/threshold, we're not in units/ms anymore but have a unitless factor.
Use a separate variable to avoid confusion.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
