In blorp_copy, when RGB surfaces are copied, we convert the
destination surface to a Red only surface, but 3 times as wide. This
introduces an implicit restriction of "mod 3" for the destination
width.
It is easier to handle the blorp split buffer offsetting with the
original RGB surface, and do the RGB=>R after this.
Suggested-by: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
If try_blorp_blit() previously returned that a blit was too large,
shrink_surface_params() will be used to update the surface parameters
for the smaller blit so the blit operation can proceed.
v2:
* Use double instead of float. (Jason)
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
We rename do_blorp_blit() to try_blorp_blit(), and add a return error
if the surface size for the blit is too large. Now, do_blorp_blit() is
rewritten to try to split the blit into smaller operations if
try_blorp_blit() fails.
Note: In this commit, try_blorp_blit() will always attempt to blit and
never return an error, which matches the previous behavior. We will
enable the size checking and splitting in a future commit.
The motivation for this splitting is that in some cases when we
flatten an image, it's dimensions grow, and this can then exceed the
programmable hardware limits. An example is w-tiled+MSAA blits.
v2:
* Use double instead of float. (Jason)
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
This will be useful for splitting blits into smaller sizes.
We also make the coordinates of type double rather than float. Since
we will be splitting and scaling the coordinates, we might require
extra precision in the calculations.
v2:
* Use double instead of float. (Jason)
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Previously, blorp copy operations were CCS-unaware so you had to perform
resolves on the source and destination before performing the copy. This
commit makes blorp_copy capable of handling CCS-compressed images without
any resolves.
Reviewed-by: Topi Pohjolainen <topi.pohjolainen@intel.com>
Many of these UINT formats aren't available prior to Sky Lake so we used
UNORM formats. Using UINT formats is a bit nicer because it guarantees we
don't run into rounding issues. Also, we will need it in the next commit
for handling copies with CCS enabled.
Reviewed-by: Topi Pohjolainen <topi.pohjolainen@intel.com>
Eventually, we may want to just have a single blorp_ccs_op function that
does both clears and resolves. For now we'll stick to just making the
ccs_resolve function we have now a bit more configurable.
Reviewed-by: Topi Pohjolainen <topi.pohjolainen@intel.com>
When a pre-baked binding table is requested, no binding table is created,
instead the binding table offset (relative to surface state base address)
provided by the user is used verbatim.
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Topi Pohjolainen <topi.pohjolainen@intel.com>
We're about to start passing other things in as a sort of "VS header" for
vertex shaders and we need a place to put them. Since we want the instance
id to be one of them, it makes sense to have one vec4 that's either VUE
header or VS header. Always uploading some handy zeros makes the code a
bit simpler.
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Topi Pohjolainen <topi.pohjolainen@intel.com>
Some things may not be floats and intel CPUs are known for mangling bits
when a float type is used for copying integers.
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Topi Pohjolainen <topi.pohjolainen@intel.com>
By using offsetof() we can ensure that adding fiels to wm_inputs is always
safe as long as we maintain alignment.
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Topi Pohjolainen <topi.pohjolainen@intel.com>
Depending on how the driver using blorp implements its shader caching,
there is a small chance of shader collisions due to identical keys between
blit and clear programs. Adding a small shader type at the top of the key
alleviates this problem.
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Topi Pohjolainen <topi.pohjolainen@intel.com>
Previously, we always inferred it from params->dst which meant that
references to params->dst were scattered all throughout the state upload
code.
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Topi Pohjolainen <topi.pohjolainen@intel.com>
At least on Sky Lake, after emitting 3DSTATE_CONSTANT_*, you are required
to re-emit the 3DSTATE_BINDING_TABLE_POINTERS packet for the corresponding
stage. If you don't, double-buffering may fail and you may get the wrong
constants. It turns out that you need to do this even if you have no push
constants to speak of or else the next 3DSTATE_CONSTANT packet you emit for
that stage may not work correctly.
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Topi Pohjolainen <topi.pohjolainen@intel.com>
Cc: "13.0" <mesa-stable@lists.freedesktop.org>
Previously, we were creating the shader with a NULL ralloc context and then
trusting in blorp_compile_fs to clean it up. The only problem was that
blorp_compile_fs didn't clean up its context properly so we were leaking.
When I went to fix that, I realized that it couldn't because it has to
return the shader binary which is allocated off of that context and used by
the caller. The solution is to make blorp_compile_fs take a ralloc
context, allocate the nir_shaders directly off that context, and clean it
all up in whatever function creates the shader and calls blorp_compile_fs.
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Topi Pohjolainen <topi.pohjolainen@intel.com>
Reviewed-by: Timothy Arceri <timothy.arceri@collabora.com>
Cc: "12.0, 13.0" <mesa-stable@lists.freedesktop.org>
With dealing with rectangles in compressed images, you can have a width or
height that isn't a multiple of the corresponding compression block
dimension but only if that edge of your rectangle is on the edge of the
image. When we call convert_to_single_slice, it creates an 2-D image and a
set of tile offsets into that image. When detecting the right-edge and
bottom-edge cases, we weren't including the tile offsets so the assert
would misfire. This caused crashes in a few UE4 demos
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reported-by: "Eero Tamminen" <eero.t.tamminen@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98431
Cc: "13.0" <mesa-stable@lists.freedesktop.org>
Tested-by: "Eero Tamminen" <eero.t.tamminen@intel.com>
Reviewed-by: Iago Toral Quiroga <itoral@igalia.com>
Here brw_setup_vue_interpolation() is rewritten not to use the InterpQualifier
array in gl_fragment_program which will allow us to remove it.
This change also makes the code which is only used by gen4/5 more self contained
as it now has its own gen5_fragment_program struct rather than storing the map
in brw_context. This means the interpolation map will only get processed once
and will get stored in the in memory cache rather than being processed everytime
the fs changes.
Also by calling this from the fs compile code rather than from the upload code
and using the interpolation assigned there we can get rid of the
BRW_NEW_INTERPOLATION_MAP flag.
It might not seem ideal to add a gen5_fragment_program struct however by the end
of this series we will have gotten rid of all the brw_{shader_stage}_program
structs and replaced them with a generic brw_program struct so there will only
be two program structs which is better than what we have now.
V2: Don't remove BRW_NEW_INTERPOLATION_MAP from dirty_bit_map until the following
patch to fix build error.
V3 - Suggestions by Jason:
- name struct gen4_fragment_program rather than gen5_fragment_program
- don't use enum with memset()
- create interp mode set helper and simplify logic to call it
- add assert when calling function to show prog will never be NULL for
gen4/5 i.e. no Vulkan
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
When restoring something from shader cache we won't have and don't
want to create a nir_shader this change detaches the two.
There are other advantages such as being able to reuse the
shader info populated by GLSL IR.
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
In Vulkan, we want to be able to use blorp to perform clears inside of a
render pass. If blorp stomps the depth/stencil buffers packets then we'll
have to re-emit them. This gets tricky when secondary command buffers get
involved. Instead, we'll simply guarantee that the depth and stencil
buffers we pass to blorp (if any) match those already set in the hardware.
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Topi Pohjolainen <topi.pohjolainen@intel.com>
This never mattered before because the only time we used blorp
depth/stencil only was to do HiZ operations on gen6-7. It may have worked
in that case (and maybe it didn't) but slow depth clears actually do depth
rendering so they need a valid render target.
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Topi Pohjolainen <topi.pohjolainen@intel.com>
This gives a slightly smarter way to check whether or not a particular
surface exists than looking at the address.
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Topi Pohjolainen <topi.pohjolainen@intel.com>
This should now set the pipeline up properly for doing depth and/or stencil
clears by plumbing through depth/stencil test values. We are now also
emitting color calculator state for blorp operations without an actual
shader because that is where the stencil reference value goes pre-SKL.
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Topi Pohjolainen <topi.pohjolainen@intel.com>
The newly reworked depth/stencil config code can properly handle having
depth, stencil, both, or neither. We no longer need to predicate it on
having depth or stencil.
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Topi Pohjolainen <topi.pohjolainen@intel.com>
While we're here, we also make depth without HiZ work.
v2:
- Use the correct surface type for 1-D on SKL+
- Set QPitch on BDW+
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Topi Pohjolainen <topi.pohjolainen@intel.com>
We want to be able to start doing slow depth clears with blorp. This
allows us to adjust the depth we're clearing to.
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Topi Pohjolainen <topi.pohjolainen@intel.com>
Avoid the discouraged use of pragma once and a missing guard for
blorp_genX_exec.h.
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Chad Versace <chadversary@chromium.org>
Use the vertex positions described in the PRMs. This has no effect on
rendering but quiets the simulator warnings seen when the vertices
appear out of order.
Signed-off-by: Nanley Chery <nanley.g.chery@intel.com>
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
The Vulkan driver sets 3DSTATE_DRAWING_RECTANGLE once to MAX_INT x MAX_INT
at the GPU initialization time and never sets it again. The GL driver sets
it every time the framebuffer changes. Originally, blorp set it to the
size of the drawing area but meant we had to set it back in the Vulkan
driver. Instead, we can easily just do that in the GL driver's blorp_exec
implementation and not set it in blorp core.
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Anuj Phogat <anuj.phogat@gmail.com>
Previously, we relied on a driver hook for 3DSTATE_MULTISAMPLE. However,
now that Vulkan and GL use the same sample positions, we can set up
3DSTATE_MULTISAMPLE directly in blorp and delete the driver hook.
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Anuj Phogat <anuj.phogat@gmail.com>
This allows us to #undef them later if we don't want them to persist
Signed-off-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Topi Pohjolainen <topi.pohjolainen@intel.com>
