All of the affected shaders are geometry shaders... the same ones from
the similar fs changes.
The "No changes on any other platforms" comment below is not quite
right. Without the previous change to register coalescing, this
optimization caused quite a few regressions in tests that either used
gl_ClipVertex or used different interpolation modes. I observed that
with both patches applied,
glsl-1.10/execution/interpolation/interpolation-none-gl_BackSecondaryColor-smooth-vertex.shader_test
was one instruction shorter. I suspect other shaders would be similarly
affected. Since this is all based on NOS, shader-db does not reflect
it.
Haswell
total instructions in shared programs: 12954955 -> 12954918 (<.01%)
instructions in affected programs: 3603 -> 3566 (-1.03%)
helped: 37
HURT: 0
helped stats (abs) min: 1 max: 1 x̄: 1.00 x̃: 1
helped stats (rel) min: 0.21% max: 2.50% x̄: 1.99% x̃: 2.50%
95% mean confidence interval for instructions value: -1.00 -1.00
95% mean confidence interval for instructions %-change: -2.30% -1.69%
Instructions are helped.
total cycles in shared programs: 410012108 -> 410012098 (<.01%)
cycles in affected programs: 3540 -> 3530 (-0.28%)
helped: 5
HURT: 0
helped stats (abs) min: 2 max: 2 x̄: 2.00 x̃: 2
helped stats (rel) min: 0.28% max: 0.28% x̄: 0.28% x̃: 0.28%
95% mean confidence interval for cycles value: -2.00 -2.00
95% mean confidence interval for cycles %-change: -0.28% -0.28%
Cycles are helped.
Ivy Bridge
total instructions in shared programs: 11679387 -> 11679351 (<.01%)
instructions in affected programs: 3292 -> 3256 (-1.09%)
helped: 36
HURT: 0
helped stats (abs) min: 1 max: 1 x̄: 1.00 x̃: 1
helped stats (rel) min: 0.21% max: 2.50% x̄: 2.04% x̃: 2.50%
95% mean confidence interval for instructions value: -1.00 -1.00
95% mean confidence interval for instructions %-change: -2.34% -1.74%
Instructions are helped.
No changes on any other platforms.
Signed-off-by: Ian Romanick <ian.d.romanick@intel.com>
This prevents regressions in a bunch of clipping and interpolation tests
caused by the next patch (i965/vec4: Optimize OR with 0 into a MOV).
Signed-off-by: Ian Romanick <ian.d.romanick@intel.com>
The Vertex Elements are now:
* VE 1: <BaseVertex/firstvertex, BaseInstance, VertexID, InstanceID>
* VE 2: <DrawID, is-indexed-draw, 0, 0>
VE1 is it kept as it was before, VE2 additionally contains the new
system value.
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Until we set gl_BaseVertex to zero for non-indexed draw calls
both have an identical value.
The Vertex Elements are kept like that:
* VE 1: <BaseVertex/firstvertex, BaseInstance, VertexID, InstanceID>
* VE 2: <Draw ID, 0, 0, 0>
v2 (idr): Mark nir_intrinsic_load_first_vertex as "unreachable" in
emit_system_values_block and fs_visitor::nir_emit_vs_intrinsic.
Otherwise, any indirect push constant access results in an assertion
failure when we start digging through the channel_sizes array. This
fixes dEQP-VK.pipeline.push_constant.graphics_pipeline.dynamic_index_vert
on Haswell. It should be a harmless no-op for GL since indirect push
constants aren't used there.
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Fixes: e69e5c7006 "i965/vec4: load dvec3/4 uniforms first in the..."
A recent commit (see below) triggered some cases where conditional
modifier propagation and dead code elimination would cause a MAD
instruction like the following to be generated:
mad.l.f0 null, ...
Matt pointed out that fs_visitor::fixup_3src_null_dest() fixes cases
like this in the scalar backend. This commit basically ports that code
to the vec4 backend.
NOTE: I have sent a couple tests to the piglit list that reproduce this
bug *without* the commit mentioned below. This commit fixes those
tests.
Signed-off-by: Ian Romanick <ian.d.romanick@intel.com>
Reviewed-by: Matt Turner <mattst88@gmail.com>
Tested-by: Tapani Pälli <tapani.palli@intel.com>
Cc: mesa-stable@lists.freedesktop.org
Fixes: ee63933a7 ("nir: Distribute binary operations with constants into bcsel")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105704
This method is similar to the existing ::equals methods. Instead of
testing that two src_regs are equal to each other, it tests that one is
the negation of the other.
v2: Simplify various checks based on suggestions from Matt. Use
src_reg::type instead of fixed_hw_reg.type in a check. Also suggested
by Matt.
v3: Rebase on 3 years. Fix some problems with negative_equals with VF
constants. Add fs_reg::negative_equals.
v4: Replace the existing default case with BRW_REGISTER_TYPE_UB,
BRW_REGISTER_TYPE_B, and BRW_REGISTER_TYPE_NF. Suggested by Matt.
Expand the FINISHME comment to better explain why it isn't already
finished.
Signed-off-by: Ian Romanick <ian.d.romanick@intel.com>
Reviewed-by: Alejandro Piñeiro <apinheiro@igalia.com> [v3]
Reviewed-by: Matt Turner <mattst88@gmail.com>
v2 (idr): Don't allow CSEL with a non-float src2.
v3 (idr): Add CSEL to fs_inst::flags_written. Suggested by Matt.
v4 (idr): Only set BRW_ALIGN_16 on Gen < 10 (suggested by Matt). Don't
reset the access mode afterwards (suggested by Samuel and Matt). Add
support for CSEL not modifying the flags to more places (requested by
Matt).
Signed-off-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ian Romanick <ian.d.romanick@intel.com>
Reviewed-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com> [v3]
Reviewed-by: Matt Turner <mattst88@gmail.com>
These days, we're just passing a pointer to a prog_data field, which
we already have access to. We can just use it directly.
(In the past, it was a pointer to a separate value.)
Reviewed-by: Iago Toral Quiroga <itoral@igalia.com>
This allows representing conditional mods and predicates on f1.0-f1.1
at the IR level by adding an extra bit to the flag_subreg
backend_instruction field.
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
First we move double_inputs_read into a vs struct in the union,
double_inputs_read is only used for vs inputs so this will
save space and also allows us to add a new double_inputs field.
We add the new field because c2acf97fcc changed the behaviour
of double_inputs_read, and while it's no longer used to track
actual reads in i965 we do still want to track this for gallium
drivers.
Reviewed-by: Marek Olšák <marek.olsak@amd.com>
Older OpenGL defines two equations for converting from signed-normalized
to floating point data. These are:
f = (2c + 1)/(2^b - 1) (equation 2.2)
f = max{c/2^(b-1) - 1), -1.0} (equation 2.3)
Both OpenGL 4.2+ and OpenGL ES 3.0+ mandate that equation 2.3 is to be
used in all scenarios, and remove equation 2.2. DirectX uses equation
2.3 as well. Intel hardware only supports equation 2.3, so Gen7.5+
systems that use the vertex fetcher hardware to do the conversions
always get formula 2.3.
This can make a big difference for 10-10-10-2 formats - the 2-bit value
can represent 0 with equation 2.3, and cannot with equation 2.2.
Ivybridge and older were using equation 2.2 for OpenGL, and 2.3 for ES.
Now that Ivybridge supports OpenGL 4.2, this is wrong - we need to use
the new rules, at least in core profile. That would leave Gen4-6 doing
something different than all other hardware, which seems...lame.
With context version promotion, applications that requested a pre-4.2
context may get promoted to 4.2, and thus get the new rules. Zero cases
have been reported of this being a problem. However, we've received a
report that following the old rules breaks expectations. SuperTuxKart
apparently renders the cars red when following equation 2.2, and works
correctly when following equation 2.3:
https://github.com/supertuxkart/stk-code/issues/2885#issuecomment-353858405
So, this patch deletes the legacy equation 2.2 support entirely, making
all hardware and APIs consistently use the new equation 2.3 rules.
If we ever find an application that truly requires the old formula, then
we'd likely want that application to work on modern hardware, too. We'd
likely restore this support as a driconf option. Until then, drop it.
This commit will regress Piglit's draw-vertices-2101010 test on
pre-Haswell without the corresponding Piglit patch to accept either
formula (commit 35daaa1695ea01eb85bc02f9be9b6ebd1a7113a1):
draw-vertices-2101010: Accept either SNORM conversion formula.
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Reviewed-by: Ian Romanick <ian.d.romanick@intel.com>
Reviewed-by: Chris Forbes <chrisforbes@google.com>
When we split an instruction that reads an uniform value
(vstride 0) we need to respect the vstride on the second
half of the instruction (that is, the second half should
read the same region as the first).
We were doing this already, but we didn't account for
stages that have interleaved input attributes which also
have a vstride of 0 and need the same treatment.
Fixes the following on Haswell:
KHR-GL45.enhanced_layouts.varying_locations
KHR-GL45.enhanced_layouts.varying_array_locations
KHR-GL45.enhanced_layouts.varying_structure_locations
Reviewed-by: Matt Turner <mattst88@gmail.com>
Acked-by: Andres Gomez <agomez@igalia.com>
The caller can now use brw_stage_prog_data::program_size which is set
by the brw_compile_* functions.
Cc: Jason Ekstrand <jason@jlekstrand.net>
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
This will be used by the on disk shader cache.
v2:
* Set in brw_compile_* rather than brw_codegen_*. (Jason)
Signed-off-by: Timothy Arceri <timothy.arceri@collabora.com>
[jordan.l.justen@intel.com: Only add to brw_stage_prog_data]
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
Now that we're always growing the param array as-needed, we can
allocate the param array in common code and stop repeating the
allocation everywere. In order to keep things sane, we ralloc the
[pull_]param array off of the compile context and then steal it back
to a NULL context later. This doesn't get us all the way to where
prog_data::[pull_]param is purely an out parameter of the back-end
compiler but it gets us a lot closer.
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
This moves us away to the array of pointers model and onto a model where
each param is represented by a generic uint32_t handle. We reserve 2^16
of these handles for builtins that get generated by somewhere inside the
compiler and have well-defined meanings. Generic params have handles
whose meanings are defined by the driver.
The primary downside to this new approach is that it moves a little bit
of the work that we would normally do at compile time to draw time. On
my laptop this hurts OglBatch6 by no more than 1% and doesn't seem to
have any measurable affect on OglBatch7. So, while this may come back
to bite us, it doesn't look too bad.
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
These vaguely corresponded to the hardware encodings, but that is purely
historical at this point. Reorder them so we stop making things "almost
work" when mixing enums.
The ordering has been closen so that no enum value is the same as a
compatible hardware encoding.
Reviewed-by: Scott D Phillips <scott.d.phillips@intel.com>
This patch starts uploading UBO data via 3DSTATE_CONSTANT_* packets,
and updates the compiler to know that there's extra payload data, so
things continue working. However, it still issues pull loads for all
data. I wanted to separate the two aspects for greater bisectability.
v2: Update for new intel_bufferobj_buffer parameter.
Reviewed-by: Matt Turner <mattst88@gmail.com>
In 5f2fe9302c is_geminilake was introduced for the differenciate
broxton from geminilake. Unfortunately I failed as verifying that
is_broxton is throughout the code base to mean Gen9lp.
Fixes: 5f2fe9302c ("intel: common: add flag to identify platforms by name")
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
v1: By Ben Widawsky <benjamin.widawsky@intel.com>
v2: v1 had an assert only for VS. Add the restriction for GS, HS and
DS as well and make sure the allocated sizes are not multiple of 3.
v3: Move the entry_size checks in to compiler code (Ken)
Signed-off-by: Anuj Phogat <anuj.phogat@gmail.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Reorder the uniforms to load first the dvec4-aligned variables in the
push constant buffer and then push the vec4-aligned ones. It takes
into account that the relocated uniforms should be aligned to their
channel size.
This fixes a bug were the dvec3/4 might be loaded one part on a GRF and
the rest in next GRF, so the region parameters to read that could break
the HW rules.
v2:
- Fix broken logic.
- Add a comment to explain what should be needed to optimise the usage
of the push constant buffer slots, as this patch does not pack the
uniforms.
v3:
- Implemented the push constant buffer usage optimization.
Signed-off-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Cc: "17.1" <mesa-stable@lists.freedesktop.org>
Acked-by: Francisco Jerez <currojerez@riseup.net>
We're already doing this in the FS back-end. This just does the same
thing in the vec4 back-end.
Reviewed-by: Alejandro Piñeiro <apinheiro@igalia.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
The NIR pass already handles remapping system values to attributes for
us so we delete the system value code as part of the conversion.
We also change nir_lower_vs_inputs to take an explicit inputs_read
bitmask and pass in the inputs_read from prog_data instead from pulling
it out of NIR. This is because the version in prog_data may get
EDGEFLAG added to it on some old platforms.
Reviewed-by: Alejandro Piñeiro <apinheiro@igalia.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
We also add a nice little comment to make it more clear exactly what
happens with the edge flag copy.
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Commit e1af20f18a changed the shader_info
from being embedded into being just a pointer. The idea was that
sharing the shader_info between NIR and GLSL would be easier if it were
a pointer pointing to the same shader_info struct. This, however, has
caused a few problems:
1) There are many things which generate NIR without GLSL. This means
we have to support both NIR shaders which come from GLSL and ones
that don't and need to have an info elsewhere.
2) The solution to (1) raises all sorts of ownership issues which have
to be resolved with ralloc_parent checks.
3) Ever since 00620782c9, we've been
using nir_gather_info to fill out the final shader_info. Thanks to
cloning and the above ownership issues, the nir_shader::info may not
point back to the gl_shader anymore and so we have to do a copy of
the shader_info from NIR back to GLSL anyway.
All of these issues go away if we just embed the shader_info in the
nir_shader. There's a little downside of having to copy it back after
calling nir_gather_info but, as explained above, we have to do that
anyway.
Acked-by: Timothy Arceri <tarceri@itsqueeze.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
On gen7, the swizzles used in DF align16 instructions works for element
size of 32 bits, so we can address only 2 consecutive DFs. As we assumed that
in the rest of the code and prepare the instructions for this (scalarize_df()),
we need to set it to two again.
However, for DF align1 instructions, a width of 2 is wrong as we are not
reading the data we want. For example, an uniform would have a region of
<0, 2, 1> so it would repeat the first 2 DFs, when we wanted to access
to the first 4.
This patch sets the default one to 4 and then modifies the width of
align16 instruction's DF sources when we translate the logical swizzle
to the physical one.
v2:
- Remove conditional (Curro).
Signed-off-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Cc: "17.1" <mesa-stable@lists.freedesktop.org>
Reviewed-by: Francisco Jerez <currojerez@riseup.net>
From IVB PRM, vol4, part3, "General Restrictions on Regioning
Parameters":
"If ExecSize = Width and HorzStride ≠ 0, VertStride must
be set to Width * HorzStride."
In next patch, we are going to modify the region parameter for
uniforms and vgrf. For uniforms that are the source of
DF align1 instructions, they will have <0, 4, 1> regioning and
the execsize for those instructions will be 4, so they will break
the regioning rule. This will be the same for VGRF sources where
we use the vstride == 0 exploit.
As we know we are not going to cross the GRF boundary with that
execsize and parameters (not even with the exploit), we just fix
the vstride here.
v2:
- Move is_align1_df() (Curro)
- Refactor exec_size == width calculation (Curro)
Signed-off-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Cc: "17.1" <mesa-stable@lists.freedesktop.org>
Reviewed-by: Francisco Jerez <currojerez@riseup.net>
Curro pointed out that I should not just check for MACH, but use
the reads_accumulator_implicitly() helper, which would also prevent
the same bug with MAC and SADA2 (if we ever decide to use them).
Cc: mesa-stable@lists.freedesktop.org
Reviewed-by: Francisco Jerez <currojerez@riseup.net>
opt_register_coalesce() was optimizing sequences such as:
mul(8) acc0:D, attr18.xyyy:D, attr19.xyyy:D
mach(8) vgrf5.xy:D, attr18.xyyy:D, attr19.xyyy:D
mov(8) m4.zw:F, vgrf5.xxxy:F
into:
mul(8) acc0:D, attr18.xyyy:D, attr19.xyyy:D
mach(8) m4.zw:D, attr18.xxxy:D, attr19.xxxy:D
This doesn't work - if we're going to reswizzle MACH, we'd need to
reswizzle the MUL as well. Here, the MUL fills the accumulator's .zw
components with attr18.yy * attr19.yy. But the MACH instruction expects
.z to contain attr18.x * attr19.x. Bogus results ensue.
No change in shader-db on Haswell. Prevents regressions in Timothy's
patches to use enhanced layouts for varying packing (which rearrange
code just enough to trigger this pre-existing bug, but were fine
themselves).
Acked-by: Timothy Arceri <tarceri@itsqueeze.com>
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
This way we can set the destination type as double to all these new opcodes,
avoiding any optimizer's confusion that was happening before.
Signed-off-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
[ Francisco Jerez: Drop no_spill workaround originally needed due to
the bogus destination type of VEC4_OPCODE_FROM_DOUBLE. ]
Reviewed-by: Francisco Jerez <currojerez@riseup.net>
Keep the original type when dealing with null registers. Especially
because we do no want to introduce an implicit conversion between
types that could affect the conditional flags.
This affects especially when the original type is DF, and we are working
on Ivybridge/Baytrail.
v2 (Curro)
- Fix typo.
- Use retype() instead of applying the type directly.
- Remove unneeded retype.
Reviewed-by: Francisco Jerez <currojerez@riseup.net>
We need to split DF instructions in two on IVB/BYT as it needs an
execsize 8 to process 4 DF values (one GRF in total).
v2:
- Rename helper and make it static inline function (Matt).
- Fix indention and add braces (Matt).
v3:
- Don't edit IR instruction when doubling exec_size (Curro)
- Add comment into the code (Curro).
- Manage ARF registers like the others (Curro)
v4:
- Add get_exec_type() function and use it to calculate the execution
size.
Signed-off-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
[ Francisco Jerez: Fix bogus 'type != BAD_FILE' check. Take
destination type as execution type where there is no valid source.
Assert-fail if the deduced execution type is byte. Clarify comment
in get_lowered_simd_width(). Move SIMD width workaround outside of
'if (...inst->size_written > REG_SIZE)' conditional block, since the
problem should be independent of whether the amount of data written
by the instruction is greater or lower than a GRF. Drop redundant
is_ivb_df definition. Drop bogus inst->exec_size < 8 check.
Simplify channel group assertion. ]
Reviewed-by: Francisco Jerez <currojerez@riseup.net>
Mostly a dummy git mv with a couple of noticable parts:
- With the earlier header cleanups, nothing in src/intel depends
files from src/mesa/drivers/dri/i965/
- Both Autoconf and Android builds are addressed. Thanks to Mauro and
Tapani for the fixups in the latter
- brw_util.[ch] is not really compiler specific, so it's moved to i965.
v2:
- move brw_eu_defines.h instead of brw_defines.h
- remove no-longer applicable includes
- add missing vulkan/ prefix in the Android build (thanks Tapani)
v3:
- don't list brw_defines.h in src/intel/Makefile.sources (Jason)
- rebase on top of the oa patches
[Emil Velikov: commit message, various small fixes througout]
Signed-off-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Jason Ekstrand <jason@jlekstrand.net>
2017-03-13 11:16:34 +00:00
Renamed from src/mesa/drivers/dri/i965/brw_vec4.cpp (Browse further)
