Makes it even longer, but at least it's consistent with button and key state.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Jason Gerecke <jason.gerecke@wacom.com>
For the puck/lens cursor tool we need to artificially reduce proximity
detection. These tools are usually used in a relative mode (i.e. like a mouse)
and thus require lifting and resetting the tool multiple times to move across
the screen. The tablets' distance detection goes too far, requiring the user
to lift the device several cm on every move. This is uncomfortable.
Introduce an artificial distance threshold for the devices with the default
value taken from the X.Org wacom driver. If a tool is in proximity but outside
of this range, fake proximity events accordingly.
If a button was pressed while we were out of range we discard that event and
send it later when we enter proximity again.
This is the simple implementation that only takes one proximity out value (the
one from the wacom driver) and applies it to all. Those devices that support a
button/lens tool and have a different default threshold are well out of date.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
[rebased, tests updated for new axis percentage behavior (8d76734f)]
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
The only time we need this is on proximity in, so move it to where we handle
that to have better locality. And rather than looping through and checking
each bit, just memcpy the axis capabilities, because by definition they
represent the set of axes that can possibly change.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
This will be set when the tool comes into proximity later.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Now that we don't provide an API anymore to access the absolute value of the
wheel and the axes are handled separately, we can safely store the wheel delta
in the normal axis array.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
We know when one of the bits is set we need to send an event
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
We know when one of the bits is set we need to send an event
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Process the axes explicitly, rather than having a loop that needs special
casing for most axes anyway. And since we do the axes one-by-one, we can use
the evdev axis code directly rather than the axis_to_evcode helper.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
The wheel is the only one axis that has actual deltas, all others have
straightforward deltas that we don't need to care about, the caller can
calculate those where needed.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Only the wheel has a discrete value, no need to keep arrays for a single
value.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
If a tool wears out, it may have a pre-loaded pressure offset. In that case,
even when the tool is not physically in contact with the tablet surface it
will send pressure events.
Use automatic pressure offset detection, similar to what the X.Org wacom
driver does. On proximity-in, check the pressure and if the distance is above
50% of the range and the pressure is nonzero but below 20% of the range, use
that value as pressure offset.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Ping Cheng <pingc@wacom.com>
If we have pressure but not BTN_TOUCH, force the pressure to 0. Otherwise,
force distance to 0.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Keep pressure and distance mutually exclusive regardless which one of the two
updates.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
If it's a finger, it's a touchscreen or a touchpad, not a tablet.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Behavior for axis events in the same event frame as the BTN_TOUCH is to
always send axis events before any tip state.
Behavior for button events in the same event frame as the BTN_TOUCH is to
order button events to happen when the tip is in proximity, i.e. after the tip
event on tip down and before the tip event on tip up.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Some tablets cannot be differentiated by pid/vid alone, use the device path
instead - that gives libwacom the ability to extract the information required
to handle the device (libwacom doesn't open the path, it just reads through
the sysfs entry of the device).
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Only the cursor tool has rotation encoded as tilt, so if we don't have the
mouse tool we don't have rotation. We still need to check for ABS_Z separately
though.
Crashes Waltop tablets that have tilt x/y but no cursor/lens tool. We'd thus
never hit the rotation-z condition in tablet_check_notify_axes() and
eventually try to dereference a non-existing ABS_Z axis.
https://bugs.freedesktop.org/show_bug.cgi?id=90885
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
If a tool is in proximity when we init, send a proximity event immediately.
This is only partially reliable due to the current kernel behavior:
* if the tool comes into proximity when there is no evdev client, the device
won't send any events and must be lifted out-of-proximity first. Patch is in
the works, see https://patchwork.kernel.org/patch/5924611/
* before 3.19, if the tool was in proximity (with an evdev client attached),
but goes out of proximity and back in with no client connected, we get an
immediate proximity out event from the kernel once we connect to the device
and no further events after that.
See kernel commit b905811a49bcd6e6726ce5bbb591f57aaddfd3be
Otherwise, things work as expected. The above should be fixed in the kernel
anyway.
Note that this changes the order of events during a udev seat init, before we
had all DEVICE_ADDED events in a row, now the proximity event may be
interspersed.
Reported-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Equivalent to the pointer axis function - it gets the mouse wheel clicks from
the tablet mouse.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Stephen Chandler Paul <thatslyude@gmail.com>
