Add an accessor for device rfkill type and use that instead of
GObject properties, and also use that accessor when claiming a
new device instead of checking NM_IS_DEVICE_xxxx(). Allows us
to move one step closer to making WiMAX a plugin.
ether_aton() allows addresses like "0:1:2:3:4:5" which was casusing
some problems when reading connections after switching callers of
ether_aton() to nm_utils_hwaddr_aton().
NetworkManager[815]: merge_ip6_configs: assertion `src != NULL' failed
Calling ip6_config_merge_and_apply() with a NULL src_config is fine
since that's what happens during RA or DHCP lease changes.
Reported by Johannes Sjölund
The RDNSS and DNSSL failure cases wouldn't clear out the idle
handler of a previous success (if that success hadn't fired yet);
it seems pointless to signal success and then immediately fail.
Second, it would cause a dangling GSource if the device was
removed or NM quit at the right time.
The errors appeared due to calling GetAccessPoints() on removed devices:
nm_device_wifi_get_access_points: error getting access points: Method "GetAccessPoints" with signature "" on interface "org.freedesktop.NetworkManager.Device.Wireless" doesn't exist
NMClient and NMDevice used a 'lazy' approach for getting stuff from D-Bus, i.e.
requesting data from NM when they are asked for. However, for some cases, like
removing devices it is not optimal. libnm-glib will never see a device that was
removed, but not added during NMClient's lifetime.
So let's get devices list in NMClient's constructor and device properties
in NMDevice constructor to have the data from the beginning.
In cases where the actual password is non-ASCII, it may not be
possible to deliver the 802.1x password as a D-Bus string. Instead
provide an alternate field holding the password as a byte array.
In cases where both a password and password-raw are supplied,
password is preferred.
The 802.1x password for MS-CHAPv2 can be up to 256 UCS-2 characters,
so we need to validate the password as UTF-8 to make sure we don't
reject valid passwords containing non-ASCII characters
Currently slaves only wait for the master device to be present. This is
insufficient, we want to wait for the master connection to be activated.
Signed-off-by: Thomas Graf <tgraf@redhat.com>
I only install libnl-3.2.3 on my system, and I met an error:
In file included from ../../src/nm-netlink-monitor.h:93:0,
from nm-vpn-connection.c:48:
../../src/nm-netlink-compat.h:210:5: error: "HAVE_LIBNL1" is not defined
../../src/nm-netlink-compat.h:210:20: error: "HAVE_LIBNL2" is not defined
make[5]: *** [libvpn_manager_la-nm-vpn-connection.lo] Error 1
Signed-off-by: Weiping Pan <wpan@redhat.com>
Revert the DEVICE and suffix bits for the connection name; there's
a few problems with this. It adds the DEVICE value for connections
regardless of what type they, even in cases where it's not hugely
useful (ie basic wired). We used to do this, but stopped doing it
because it has zero relevance to a large number of users. Instead,
the UI itself should do this where appropriate. That probably means
that 'nmcli' and other tools should give more information about
the components of a connection (like a slave device's master) and
GUI tools would show that in detailed connection information but
not in the at-a-glance status or tooltips. Second, if more
more advanced users wish this information to show up in the name
they can always set the name themselves, or name the ifcfg file
something like "ifcfg-bond1-slave-of-eth0" too.
nm_utils_hwaddr_ntoa() and nm_utils_hwaddr_aton() are like
ether_ntoa()/ether_aton(), but handle IPoIB too.
nm_utils_hwaddr_atoba() is like _aton() but returns a GByteArray,
since that's what's wanted in many places.
Also remove nm_ether_ntop() and replace uses of it with
nm_utils_hwaddr_ntoa().
