RFCs actually expect to honor the lifetime. See for example [1].
This is just not right, and totally arbitrary. It was added
when our libndp based implementation was added, but unclear
why this was done (beyond the code comment).
[1] page 204, v6LC.2.2.25: Processing Router Advertisement DNS (Host
only) at https://ipv6ready.org/docs/Core_Conformance_5_0_0.pdf
(cherry picked from commit 68528f7af5)
There is no actual change in behavior, because "struct nd_opt_hdr"
as two uint8_t, so in practice this struct was always packed already.
But make it explicit, because it's clear that we use these structs
to set the binary message and they need a well defined (packed) memory
layout.
(cherry picked from commit e3c464b56c)
Currently if we detect that a scan finished in
_scan_notify_is_scanning(), we call immediately _scan_kickoff() (which
might start a new scan) and then we check again whether the device can
autoactivate or whether to remove the wifi-scan pending action.
This means that if the scan takes long enough, when
_scan_notify_is_scanning() is called, it is already time to start
another scan and the device activation will be delayed. It will be
delayed until the scan duration becomes shorter than the
exponentially-growing periodic scan interval.
Fix this by delaying the next scan immediately after a scan result.
Co-authored-by: Thomas Haller <thaller@redhat.com>
https://gitlab.freedesktop.org/NetworkManager/NetworkManager/-/issues/574
(cherry picked from commit 16d649ea92)
According to RFC3315 section 15.12, Information-request messages can't
include a IA option (such as IA_NA or IA_PD).
When doing stateless DHCPv6, we start the client in the appropriate
mode to issue an Information-request message: with "-S" for dhclient or
calling sd_dhcp6_client_set_information_request(TRUE) for systemd.
However, if we need a prefix later, the client must be restarted to
ask the prefix. Currently both dhclient and systemd clients are still
configured to send an Information-request with prefixes. Fix that.
(cherry picked from commit 6ed95bd8e5)
The BOOTIF MAC address can be prefixed with a hardware address
type. Typically it is 01 (for ethernet), but the legacy network module
accepts (and strips) any byte value.
It seems wrong to take any address type without validation. In
addition to "01", also accept a zero type which, according to the
bugzilla below, is used in some configurations to mean "undefined".
While at it, also accept ':' as separator for the first byte.
https://bugzilla.redhat.com/show_bug.cgi?id=1904099https://gitlab.freedesktop.org/NetworkManager/NetworkManager/-/merge_requests/713
(cherry picked from commit 6069ef4b8b)
When building without "more-asserts" and LTO enabled, we can get
a warning about uninitalized "obj" variable:
src/platform/nm-linux-platform.c: In function 'ip_route_add':
src/platform/nm-platform.c:4761:24: warning: 'MEM[(struct NMPlatformIPRoute *)&obj + 24B].rt_source' may be used uninitialized in this function [-Wmaybe-uninitialized]
4761 | route->rt_source = nmp_utils_ip_config_source_round_trip_rtprot(route->rt_source);
| ^
src/platform/nm-platform.h:2139:25: warning: 'BIT_FIELD_REF <MEM[(const struct NMPlatformIPRoute *)&obj + 24B], 8, 72>' may be used uninitialized in this function [-Wmaybe-uninitialized]
2139 | return r->table_any ? 254u /* RT_TABLE_MAIN */
|
That is due to the "default" switch case which was unhandled
when building without more-asserts". Avoid that by reworking the
code.
(cherry picked from commit fc6475bbf7)
On copr builds, the unit tests sometimes fail to create a veth
interface. In those cases, kernel rejects the netlink request
with EPERM. copr uses mock on Fedora 33 hosts.
I think this is a kernel bug. Add a workaround by retrying a few times.
(cherry picked from commit 02f4b0cbd5)
"build_clean.sh" (and "build.sh") scripts can both create a source
tarball (via `make dist`/`make distcheck`), an SRPM (and a spec file),
or build RPMs from the SRPM.
Note that the generated spec file has various options, like
%bcond_without nmtui
%bcond_without debug
%bcond_without test
When building an RPM from the SRPM, you can specify the "--with" or
"--without" option for rpmbuild. This is also what the "-w" / "-W" options
for "build_clean.sh" do.
However, the SRPM still has the intrinsic defaults, and if you later
build an RPM from it, you would have to pass "--with" / "--without"
to rpmbuild.
Often that is not conveniently possible, for example, when you build the
SRPM in koji.
Extend the scripts so that also the defaults for "-w debug" and "-w
test" can be specified when generating the SRPM. You can do that with
the new options "--default-for-{debug,test}" to "build_clean.sh".
Alternatively, it suffices to specify the previously supported
"-w" / "-W" options. That way, we will pass those options to rpmbuild,
but also set them as defaults in the generate spec file. The new
options "--default-for-{debug,test}" are only needed if you want
the default in the spec file to be different then what you use
when creating the SRPM.
(cherry picked from commit a3f2cee0e6)
We always run the unit tests during package build and also enable all compiler
warnings. However, by default we used to ignore failures. That is, because
rebuilding a package on another, future distro led to frequent, annoying build
failures. Especially compiler warnings appear easily when using a
different compiler version.
The default mostly matters here when you want to build the package in
brew/koji, where you don't have a possibility to explicitly select the
build option.
Note that rpmdiff detects failures in the build log, and thus we usually
would not miss failures for builds we add to errata. Also, all our CI
tests build packages with a manner where they would not allow a failure
of the unit tests. So, we run these unit tests frequently and in a
manner where we notice a failure.
For rhel-9 builds, change the default here and let test failures and
compiler warnings be fatal to the build.
(cherry picked from commit e68e5c0a4c)
By default, "build_clean.sh" script likes to automatically add "-w test"
-- unless the user specified "-w test" or "-W test" on the command line.
That is mostly fine. However, the spec file has an internal default for the
"test" option. So if you want to use the default that gets determined
by the spec file, then we should suppress that automatism.
(cherry picked from commit 3bf367594a)
We cannot drop the reference count to zero while having
no lock. Otherwise, another thread might race doing
s = nm_ref_string_new("...");
nm_ref_string_unref(s);
and already successfully delete the instance.
Hitting this race should be rather difficult, especially because
we tend to use NMRefString only from one thread. But still, access
to global variables must be race free.
Fixes: 908fadec96 ('shared: add NMRefString')
(cherry picked from commit 3490a09a7d)
GObject's dispose() functions may be called multiple times
to break reference cycles.
As dispose() calls _init_release_all(), the object might
already be partially destroyed.
Fixes: ce0e898fb4 ('libnm: refactor caching of D-Bus objects in NMClient')
(cherry picked from commit ef6edd8dbd)
wpa_supplicant has a property "scanning" and a "state=scanning".
Previously, NetworkManager considered both parts to indicate whether
supplicant is currently scanning (if either the property or the state
indicated scanning, it took that as indication for scanning).
If NetworkManager thinks that supplicant is scanning, it suppresses
explicit "Scan" requests. That alone is not severe, because the "Scan"
request is only to trigger a scan in supplicant (which supplicant
possibly is already doing in state "scanning").
However, what is severe is that NetworkManager will also block autoconnect
while supplicant is scanning. That is because NetworkManager wants to get
a complete scan result before deciding which network to connect to.
It seems that wpa_supplicant can get into "state=scanning" and stay
there indefinitely. This prevents NetworkManager from autoactivating
a profile.
Fix that, to only honor the "scanning" property.
https://gitlab.freedesktop.org/NetworkManager/NetworkManager/-/issues/597
Fixes: b83f07916a ('supplicant: large rework of wpa_supplicant handling')
(cherry picked from commit 8cadfed2fe)
During shutdown, NM always tries to remove from ovsdb all bridges,
ports, interfaces that it previously added. Currently NM doesn't run
the main loop during shutdown and so it's not possible to perform
asynchronous operations. In particular, the NMOvsdb singleton is
disposed in a destructor where it's not possible to send out all the
queued deletions.
The result is that NM deletes only one OVS interface, keeping the
others. This needs to be fixed, but requires a rework of the shutdown
procedure that involves many parts of NM.
Even when a better shutdown procedure will be implemented, we should
support an unclean shutdown caused by e.g. a kernel panic or a NM
crash. In these cases, the interfaces added by NM would still linger
in the ovsdb.
Delete all those interface at NM startup. If there are connections
profiles for them, NM will create them again.
https://bugzilla.redhat.com/show_bug.cgi?id=1861296https://gitlab.freedesktop.org/NetworkManager/NetworkManager/-/merge_requests/700
(cherry picked from commit e5113a7fd9)
g_hash_table_iter_next() wants a (gpointer *), not an (int *).
Fixes: f70ee67058 ('dns: sd-resolved: reset interface configuration on deactivation')
(cherry picked from commit 526b484be1)
We now always use SetLinkDefaultRoute(), but that API was only added in
systemd v240 ([1]).
We could just always call the non-existing method, and ignore the
error. However, that feels ugly. Would systemd-resolved log warnings
about that? Should we suppress all messages about that failure (not
good for debugging).
Instead, make an effort to detect support of the function, and avoid
calling it. That is significantly more complicated than just always
calling the method and not care.
Note that even if systemd-resolved does not support SetLinkDefaultRoute(),
we cannot do anything smart about that. We would simply rely on
systemd-resolved (hopefully) doing the right thing automatically.
That's better and simpler than explicitly adding a "~." domain in
the fallback case.
Also, detecting support is straight forward in the common case, where
there is either success or a clear "org.freedesktop.DBus.Error.UnknownMethod"
error. In cases where there is any other failure, we don't really know.
In that case, we keep trying to use the API under the assumption that
it should work.
[1] https://github.com/systemd/systemd/commit/7 ## 7673795dcf5797491e7f785cbf5077d29a15db4
(cherry picked from commit 44ebb99cfa)
When the DNS settings change, we update the request_queue_lst_head list,
with all the requests we want to send.
Then, send_updates() will try to send it. It might not do it right away,
if resolved is not on the bus or the D-Bus connection is not fully inialized
(meaning, we don't know the name owner yet). In those cases, we would
keep the list of requests, and send them later.
However, when sending them, we would also forget about the configuration.
That means, if you restart systemd-resolved, then the daemon drops off
the bus and reappears. I think that systemd-resolved in fact persists
the configuration during restart. So, usually the settings are still the
same after restart. However, we should do better here: if the service
appears, we should send the settings again.
This means to not forget the requests after we send them once -- at
least, until a new update replaces them.
(cherry picked from commit 4fc44952f7)
We will need these changes next:
- add "self" and "ifindex" fields to RequestItem struct. We will
pass on these structs are user-data for the callbacks, so that
we afterwards know which request completed.
- add DBUS_OP_SET_LINK_DEFAULT_ROUTE global variable. We don't
clone the "operation" string but use string literals. However,
string literals are not guaranteed to be deduplicated, so we
should only compare them with strcmp(). The static variable
avoids this: we can use pointer equality to compare it.
This will be used next.
(cherry picked from commit 8af6647cda)
If the same MAC address is set on both the bridge connection and the
interface connection, and the interface is local, NM currently sets
the hwaddr record in both Bridge and Interface ovsdb tables. As a
result, ovs complains with error:
bridge|ERR|interface br0: ignoring mac in Interface record (use Bridge record to set local port's mac)
Avoid this error: if the bridge and interface MACs are the same, just
set the address in the Bridge table; if they are different, give a
more detailed warning and ignore the interface MAC.
https://bugzilla.redhat.com/show_bug.cgi?id=1899745
(cherry picked from commit c4beaac67b)
The parser checks if the first token of an ip= argument is an IP
address to determine which of the two possible syntaxes is used:
ip=<interface>:{dhcp|on|any|dhcp6|auto6}[:[<mtu>][:<macaddr>]]
ip=<client-IP>:[<peer>]:<gateway-IP>:<netmask>:<client_hostname>:<interface>:{none|off|dhcp|on|any|dhcp6|auto6|ibft}[:[<mtu>][:<macaddr>]]
This works as long as the first token is not empty, which - according
to the dracut.cmdline man page - seems to be guaranteed.
However, the network-legacy dracut plugin accepts an empty interface
or client IP. Also, if a user needs DHCP and wants to specify a
hostname, the only possible syntax is:
ip=::::<hostname>::dhcp
Change the parser to check the second token instead, similarly to what
the network-legacy module does [1].
[1] https://github.com/dracutdevs/dracut/blob/050/modules.d/40network/net-lib.sh#L490https://bugzilla.redhat.com/show_bug.cgi?id=1900260https://gitlab.freedesktop.org/NetworkManager/NetworkManager/-/merge_requests/693
(cherry picked from commit b0c018830e)
If the interface is the DNS default route but has no domain, its name
servers were not sent to systemd-resolved. Fix this.
Fixes: ee9fab0361 ('dns: fix handling default routing domains with systemd-resolved')
(cherry picked from commit 195cbf3cee)
Change the generator to disable by default IP configuration for the
parent connection of a VLAN, because that is what a user would expect
and what the legacy module does. Of course if the user explicitly
configures DHCP or an address for the parent interface, that overrides
the default.
Note that now the generator always creates a connection for the parent
interface. Before this commit, it did only when there was an explicit
ip= argument for the parent interface.
https://gitlab.freedesktop.org/NetworkManager/NetworkManager/-/issues/509
(cherry picked from commit f2e51ace68)
The command line parser looks for a dot or a colon to determine
whether the first token in a ip= argument is a IPv4 address (dot), an
IPv6 address (colon) or an interface name (none). This strategy
doesn't work for interface names containing a dot (typically VLANs).
Instead, try to parse the IPv4/IPv6 address in the token; if this
fails then consider the token as an interface name.
https://gitlab.freedesktop.org/NetworkManager/NetworkManager/-/issues/581
(cherry picked from commit 4aa902ecf5)
