Assume that a mode can be used in either landscape or portrait
orientation. I suppose the correct thing to do would be to
collect all the supported rotations from the CRTCs that can be used
with a specific output, but that information doesn't seem to be
readily available when these checks are done. So just assume that
either orientation is fine.
Signed-off-by: Ville Syrjälä <ville.syrjala@nokia.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
(cherry picked from commit 2e781457d4)
(cherry picked from commit aec278eb65)
Like some other LPL panels, this one reports the vertical size in cm rather
than mm.
Patch taken from Launchpad bug #380009 <https://launchpad.net/bugs/380009>
X.Org Bug 28414 <https://bugs.freedesktop.org/show_bug.cgi?id=28414>
Signed-off-by: Christopher James Halse Rogers <christopher.halse.rogers@canonical.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
(cherry picked from commit 4b88c7be8d)
cc2c73ddcb4370a7c3ad439cda4da825156c26c9's three-cent titanium tax
doesn't go too far enough. Fix the rest of the call and jmp
instructions to handle the data prefix correctly.
Reference: Intel 64 and IA-32 Architectures Software Developer's Manual
Volume 2A: Instruction Set Reference, A-M
http://www.intel.com/Assets/PDF/manual/253666.pdf
Reviewed-by: Julien Cristau <jcristau@debian.org>
Signed-off-by: Adam Jackson <ajax@redhat.com>
(cherry picked from commit bb18f27715)
Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=24348
Before (data flag ignored -> broken):
66 DATA:
e944f1 JMP 1ff6
After (fixed):
66 DATA:
e944f1ffff JMP 00001ff8
This subtle difference in the length of decoded instruction meant
that the VBE call jumped to the routine setting AX=0x14F (VBE Failed)
instead of the routine that set AX=0x4F (VBE success).
The ability to run the same code in vm86 significantly aided the
debugging of this issue. Those X.org developers who would like to drop
vm86 better take special care towards _all_ vesa bugs, as those will
expose further issues.
Patch applies easily to even xserver 1.4.2.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Tested-by: Luc Verhaegen <libv@skynet.be>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
(cherry picked from commit cc2c73ddcb)
screenInfo.numScreens is not a valid screen number, they go from 0 to
numScreens - 1.
Signed-off-by: Julien Cristau <jcristau@debian.org>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
(cherry picked from commit 8684543021)
This fixes a gamma issue on vt switch observed with KDM. VT switching away
and back would result in a black screen. Avoid this by storing the current
gamma information on init.
https://bugzilla.redhat.com/show_bug.cgi?id=533217
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
(cherry picked from commit 566d09a5cd)
When entering the VT, re-apply the saved gamma settings for each screen.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
(cherry picked from commit c050aa2f5f)
For whatever reason, some (broken) monitors will crash if you do this.
We're not actually using this information for anything, so let's just
not do it.
Originally reported as http://bugzilla.redhat.com/620333
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Adam Jackson <ajax@redhat.com>
(cherry picked from commit d2064fbb68)
crtc->{x,y} is always 0 when xf86DefaultScreenLimits() is called, so we
calculate too small an area for the initial framebuffer and force a resize
to happen.
This commit fixes the code to use desired{X,Y} instead, which contains the
initial output positions.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
(cherry picked from commit f7af00e9f0)
Commit 77c7a64e88 was introduced to fix
a cursor off by one on Intel hw, however it also move the whole crtc
into an off by one position and you could see gnom-eshell overlapping.
This commit reverts that and instead fixes the cursor hotspot
translation to work like pixman does. We add 0.5 to the cursor vector
before translating, and floor the value afterwards.
Thanks to Soeren (ssp) for pointing out where the real problem was
after explaning how pixman translates points.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
(cherry picked from commit 80d1a548d6)
Because some EnterVT code needs to remove it self from the
call chain, we need to fix all of the wrappers to correctly
unwrap/rewrap during the call chain. This is a follow-on to the fix
for bug 27114 in commit 68a9ee8370.
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Jesse Barnes <jesse.barnes@intel.com>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
Reviewed-by: Tiago Vignatti <tiago.vignatti@nokia.com>
(cherry picked from commit d75e8146c4, and
conflict from b618705 fixed up)
Signed-off-by: Julien Cristau <jcristau@debian.org>
(cherry picked from commit 3336e1f7f3)
When resetting the server, pScrn->EnterVT must be unwrapped or the
next server generation will end up wrapping the wrapper and causing an
infinite recursion on EnterVT.
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Michael Stapelberg <michael+freedesktop@stapelberg.de>
(cherry picked from commit 68a9ee8370)
When the parser sees the "keyboard" driver, it automatically (and
silently) replaces it with the constant string "kbd".
Everybody else uses malloc'd memory for the driver name, so input
device closure assumes it can use free.
Free val.str, so this crash doesn't turn into a memory leak. Whew.
Signed-off-by: Jesse Adkins <jesserayadkins@gmail.com>
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
(cherry picked from commit bce12f2956)
A simple hack to accommodate various EDID who have detailed modes that
exceed the EDID's max pixel clock. The pixel clock is only defined in
units of 10MHz and often appears as the maximum pixel code of the
detailed modes, rounded to the nearest 10MHz. Adjusting the max_clock to
include an extra 5MHz prevents the parser from rejecting the detailed
modes.
The kernel uses the same fuzz and by including it in X we can use the
same modes in X as for the console.
Fixes:
Bug 23833 - X uses different refresh rate to that set by kernel module
https://bugs.freedesktop.org/show_bug.cgi?id=23833
In the future, we will want to try harder to keep the KMS modes but at
the same time we need to apply the restrictions as specified by the
user's configuration, and need to fill in modes for fullscreen games on
fixed-mode panels.
Reported-and-tested-by: Fabio Pedretti <fabio.ped@libero.it>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
(cherry picked from commit 951605b466)
Detect if a drawable has been moved from an original crtc to a new crtc
with a lower current vblank count than the original crtc inbetween
glXSwapBuffers() calls. Reinitialize drawable's last_swap_target
before scheduling next swap if such a move has taken place.
last_swap_target defines the baseline for scheduling the next swap.
If a movement between crtc's is not taken into account, the swap may
schedule for a vblank count on the new crtc far in the future, resulting
in a apparent "hang" of the drawable for a long time.
Fixes Bugzilla bug #28383.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
(cherry picked from commit 75beadd766)
DRI2WaitSBC() didn't block if requested targetSBC wasn't yet reached.
Instead it returned a xreply with uninitialized junk return values, then
blocked the connection until targetSBC was reached.
Therefore the client didn't block, but continued with bogus return
values from glXWaitForSbcOML.
This patch fixes the problem by implementing DRI2WaitSBC similar
to the clean and proven DRI2WaitMSC implementation.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
(cherry picked from commit b3548612c7)
Conflicts:
hw/xfree86/dri2/dri2ext.c
Some pixmaps (window pixmaps and scratch pixmaps) don't have the
drawable->id set and thus DRI2 gets confused when using that field
for looking up the DRI2 drawable. Go back to using privates for getting
at the DRI2 drawable from a DrawablePtr. We need to keep the resource
tracking in place so we can remove the DRI2 drawable when the X resource
it was created for goes away. Additionally, we also now track the DRI2
drawable using a client XID so we can reclaim the DRI2 drawable even if
the client goes before the drawable and doesn't destroy the DRI2 drawable.
Tested-by: Owen W. Taylor <otaylor@fishsoup.net>
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
(cherry picked from commit 9de0e31746)
Conflicts:
hw/xfree86/dri2/dri2.c
attr->tags is an array of strings (null-terminated). When matching, match
against each string instead of each [i,end] substring in the first tag.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Jamey Sharp <jamey@minilop.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
(cherry picked from commit b5e0f6d8f4)
When Xorg is started on display :0, this ioctl is called to grant the
user the rights traditionally associated with /dev/console (before VT
support was added), such as access to local peripheral devices.
Also adds a Solaris-specific -C flag to force starting on /dev/console
instead of /dev/vt*, allowing programs like xterm -C to access the
console device.
Signed-off-by: Alan Coopersmith <alan.coopersmith@oracle.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
(cherry picked from commit 989db930d7)
Export DDX swap control status from the DRI2 module and check for it in
GLX when initializing extensions.
Reviewed-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
(cherry picked from commit 165a4a9c7d)
If a few swaps were queued leading to a throttle related block on the
client, and then the client submitted an MSC wait, one of the previous
swap wakeups could have caused the MSC wait to complete early. Add a
flag for this to prevent a swap wake from prematurely waking an MSC
waiter.
Reported-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Reviewed-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
(cherry picked from commit 5933b0abc6)
Avoid a potential swapsPending underflow by incrementing it before
ScheduleSwap, which may complete it immediately. And be sure to
decrement it again in case the schedule failed.
Reported-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Reviewed-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
(cherry picked from commit b00d435ddf)
We need to throttle swaps here in addition to when the context is made
current to avoid causing problems with clients that just swap.
Throttling here also ensures our swaps get ordered as long as we block
the client occasionally.
Reported-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Reviewed-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
(cherry picked from commit 0294ff2a5c)
Update our supported DRI2 protocol version as each driver does
DRI2ScreenInit, since depending on available kernel features, each DDX
may support different callbacks and therefore protocol.
Reviewed-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
(cherry picked from commit db1c7cb604)
A 0 swap interval means that swaps shouldn't be sync'd to vblank, so
just complete the swap immediately in that case.
Reviewed-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
(cherry picked from commit 87ca6320f2)
Handle drawable destruction and lifetime correctly.
Check whether the drawable priv is valid in DRI2SwapInterval(),
DRI2WaitSBC() and DRI2WaitMSC(); it may have gone away, so be sure to
check it before using it.
If more than 1 outstanding swap is queued, we may complete several after
an app has exited. If we free it after the first one completes and the
refcount reaches 0, we'll crash the server on subsequent completions.
So delay freeing until all swaps complete and remove the error message
as this is a normal occurence. To do this properly, we must also avoid
destroying drawables in DRI2DestroyDrawable() if a swap or wait event is
pending.
And finally, make sure we free drawables in DRI2WaitMSCComplete() if
necessary (i.e. if the refcount has reached 0 and this MSC was the last
pending event on the object).
Reported-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Reviewed-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
(cherry picked from commit 8476d99231)
Returns expected SBC after completion of swap to caller, as required by
OML_sync_control spec, instead of the last_swap_target value.
Passes target_msc, divisor, remainder, correctly for
glXSwapBuffersMscOML() call, while retaining old behaviour for simple
glXSwapBuffers() call.
An OML swap can have a 0 target_msc, which just means it needs to
satisfy the divisor/remainder equation. Pass this down to the driver as
needed so we can support it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
(cherry picked from commit b180e43977)
Added implementation for case target_sbc == 0. In that case, the
function shall schedule a wait until all pending swaps for the drawable
have completed.
Fix for non-blocking case. Old implementation returned random,
uninitialized values for (ust,msc,sbc) if it returned immediately
without scheduling a wait due to sbc >= target_sbc.
Now if function doesn't schedule a wait, but returns immediately,
it returns the (ust,msc,sbc) of the most recently completed swap,
i.e., the UST and MSC corresponding to the time when the returned
current SBC was reached.
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
(cherry picked from commit 751e8c09d3)
DRI2SwapComplete(): Increment pPriv->swap_count++; before calling
into callback for INTEL_swap_events extension, so the swap event
contains the current SBC after swap completion instead of the
previous one.
DRI2WakeupClient: Check for pPriv->target_sbc <= pPriv->swap_count,
had wrong comparison pPriv->target_sbc >= pPriv->swap_count for
unblocking of clients of DRI2WaitSBC().
Signed-off-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
(cherry picked from commit 0de4974b90)
We need to track invalid targets as well as 0 targets, so just make it
signed so our comparisons work like they should.
Reviewed-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Reported-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
(cherry picked from commit 4c8ec49826)
We need to initialize the swap target, which is passed to the driver to
schedule events. Rather than using -1 to indicate that the field is
uninitialized, just make sure we initialize it at drawable creation
time.
Reviewed-by: Mario Kleiner <mario.kleiner@tuebingen.mpg.de>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
(cherry picked from commit c4d54816f2)
Upon resume, X may try to dereference a null pointer, which has been
reported in Debian bug #507916 (http://bugs.debian.org/507916).
Jim Paris came up with a patch which solves the problem for him. Here's
a (hopefully) fixed version of his patch (without the typo).
Cc: Jim Paris <jim@jtan.com>
Signed-off-by: Cyril Brulebois <kibi@debian.org>
Reviewed-By: Matthias Hopf <mhopf@suse.de>
Signed-off-by: Keith Packard <keithp@keithp.com>
(cherry picked from commit fa6c701257)
GetPairedDevice() may not always return the keyboard, resulting in a
null-pointer dereference when accessing the XKB state.
For floating devices, the GetMaster() returns the device itself.
X.Org Bug 27573 <http://bugs.freedesktop.org/show_bug.cgi?id=27573>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Daniel Stone <daniel@fooishbar.org>
Tested-by: Ben Hutchings <ben@decadent.org.uk>
(cherry picked from commit 10de9e8ee3)
A few cursor value assignments weren't getting correctly ref counted,
causing leaks of cursor objects.
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
(cherry picked from commit cdeb2c23f8)
While VT-switched, FB access is disabled and should remain so. Trying to switch
modes in that state would re-enable it, potentially causing crashes if trying
to access it before the driver has recovered from the mode switch.
Signed-off-by: Pierre-Loup A. Griffais <pgriffais@nvidia.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
(cherry picked from commit 41bdb6c003)
We call NIDR on all devices that make it through the config backend.
Including some that have no driver assigned to them (/dev/input/mouse0 for
example). Those ones then simply get ignored by NIDR, but this should not be
noted as an error in the log file.
X_INFO is sufficient, and it may just prevent some bugreports.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Acked-by: Julien Cristau <jcristau@debian.org>
Reviewed-by: Dan Nicholson <dbn.lists@gmail.com>
(cherry picked from commit 02e86221b8)
XORG_CHECK_LINUXDOC sets the SGML search path to the parent of X11/defs.ent.
Signed-off-by: Yaakov Selkowitz <yselkowitz@users.sourceforge.net>
Acked-by: Dan Nicholson <dbn.lists@gmail.com>
Tested-by: Gaetan Nadon <memsize@videotron.ca>
(cherry picked from commit 6e0d847c27)
High resolution devices was generating integer overflow.
For instance the wacom Cintiq 21UX has an axis value up to
87000. Thus the term (dSx * (Cx - Rxlow)) is greater than
MAX_INT32.
Using 64bits integer avoids such problem.
Signed-off-by: Philippe Ribet <ribet@cena.fr>
Signed-off-by: Benjamin Tissoires <tissoire@cena.fr>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
(cherry picked from commit a780e5b363)
The main motivation here is to have the resource system clean up the
DRI2 drawable automatically so glx doesn't have to. Right now, the
glx drawable resource must be destroyed before the X drawable, so that
calling DRI2DestroyDrawable doesn't crash. By making the DRI2
drawable a resource, GLX doesn't have to worry about that and the
resource destruction order becomes irrelevant.
https://bugs.freedesktop.org/show_bug.cgi?id=26394
[Ported to 1.8 branch by ajax@redhat.com]
Signed-off-by: Kristian Høgsberg <krh@bitplanet.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
Commit 8736d112af changed the priority
ordering of the InputClass option merging to be "last match wins". This
fixes the handling of Option "Ignore" to follow that logic.
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
(cherry picked from commit adbbc66108)
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
These drivers have been deactivated for over a year now, let's not refer
potential users to them.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
(cherry picked from commit 03ccbd2579)
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
In addition to the conf files found in /etc/X11 or $sysconfdir/X11 used
for local administration, we also reserve a system directory for vendor
and package usage. The simple search path is:
/usr/share/X11/xorg.conf.d
$datadir/X11/xorg.conf.d
Files from these directories will have the lowest config priority. The
directory $datadir/X11/xorg.conf.d is exported from xorg-server.pc in
the variable "sysconfigdir". Packages should install their .conf files
to the directory specified by:
`pkg-config --variable=sysconfigdir xorg-server`
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
(cherry picked from commit 95f01bdfee)
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
There's no reason to carry all the oddities from xorg.conf like appended
hostname to the search path for xorg.conf.d. This changes it to something
very simple:
/etc/X11/<cmdline>
$sysconfdir/X11/<cmdline>
/etc/X11/xorg.conf.d
$sysconfdir/X11/xorg.conf.d
Signed-off-by: Dan Nicholson <dbn.lists@gmail.com>
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
(cherry picked from commit a1bae63dc6)
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
