Nothing actually called that function, sprinkle a few calls into existing
tests to make sure it actually works.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
The test suite (and tests) we have now all clean up nicely before calling the
final libinput_unref(). Add one where there's at least one device still
connected.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
./configure --enable-gcov adds the required flags to link everything ready for
gcov. A new make gcov target runs the test suite, then pulls all the gcov bits
together into ./test/gcov-reports/ including a summary file.
The script to pull everything out is used in libevdev too, we just have an
extra condition here to ignore the selftest gcov bits (it overwrites the
useful litest.c coverage output).
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
These conditions were never triggered by our test suite, so let's tighten up
the tests to match what we expect.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
The first event is always a device added event, skip the loops that would
paper over this. If we ever change this, the tests *should* fail.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
The second condition was never triggered because we shouldn't get anything but
keyboard events here. Drain the initial event burst and remove the two
skipping conditions that won't happen anyway.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
I'm using semaphore CI for build testing and that only provides Ubuntu 14.04
which doesn't have libevdev 1.3 or later.
Since this is a minor workaround for an error case only, revert the commit
again and leave the handling in. Less effort than having to patch around it in
semaphore.
This reverts commit 1e0736daf3.
gcov analysis showed that none of the actual testing conditions were hit, so
the test succeeded despite not actually testing anything. Which is good,
because testing for tilt normalization isn't correct anyway, tilt is in
physical degrees,
Drop the test and replace it with a test for pressure normalization instead.
We already have a similar one to check for [0, 1] range, this new one
explicitly tests for the extents.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
They weren't originally prefixed but the various tests were, but now that we
only have one test runner binary anyway, the prefix helps sorting the files
easily within e.g. gcov results.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Use the litest_assert_empty_queue() instead of manual checking, and remove the
manual checks after the function call.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
These were just there so we didn't have an unused variable warning, but
there's no reason even assigning to anything in the first place
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
We used to mark dell touchpads this way but let's make this more generic.
Nothing else used the dell touchpad model flag, so we can simply replace it.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
This requires to expand the blacklisting to be a bit more specific so we don't
initialize dwt config on devices that won't need it.
https://bugs.freedesktop.org/show_bug.cgi?id=99140
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
This should be handled by a udev rule in systemd/hwdb but that rule doesn't
apply to virtual devices.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
I've never had the log output help me identify a bug during a test run. Now
that we run all tests in the same binary the verbosity just leads to a massive
file that makes it hard to find the actual failure. Turn off LITEST_VERBOSE by
default but leave the parsing in for cases where it may come in handy.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
The Elantech touchpad on my Asus Vivobook doesn't release BTN_TOOL_FINGER on
up. If the touchpad was used before libinput initializes, the kernel filters
the event because its state is already set. We never receive it and keep
ignoring all events until the first switch to BTN_TOOL_DOUBLETAP and back.
On touchpad init sync the BTN_TOOL_FINGER state and set it accordingly. This
is the only event that can be legitimately down on init. We don't care about
BTN_TOUCH because ignoring an ongoing touch on init is generally a good idea
and we can ignore any multifinger gesture as well.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
