./configure --enable-gcov adds the required flags to link everything ready for
gcov. A new make gcov target runs the test suite, then pulls all the gcov bits
together into ./test/gcov-reports/ including a summary file.
The script to pull everything out is used in libevdev too, we just have an
extra condition here to ignore the selftest gcov bits (it overwrites the
useful litest.c coverage output).
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
When the filter code switched to raw device coordinates (bdd4264d) the input
data remained in device coordinates. Since the factor for touchpads was still
based on the physical velocity (and thus all touchpads get the same
acceleration factor for identical moves), the actual delta was dependent on
the resolution. e.g.
touchpad with 40u/mm: delta of 2/2 * accel factor 2 -> accel delta of 4/4
touchpad with 20u/mm: delta of 1/1 * accel factor 2 -> accel delta of 2/2
The normalized coordinates should be independent of the touchpad's resolution
though.
Affected by this was the standard mouse accel code and the touchpad accel
code, other filters always returned unnormalized coordinates (separate bug,
not addressed here).
This patch restores the correct behaviour for mice and touchpads
while leaving the special filters untouched. For comparision:
* 1000+dpi mice: accelerate normalized, return normalized
* touchpads: accelerate unnormalized, return normalized
* low-dpi mice: accelerate unnormalized, return unnormalized
* trackpoints: accelerate unnormalized, return unnormalized
* x230: don't touch, already does the right thing
https://bugs.freedesktop.org/show_bug.cgi?id=99383
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
We were just switching type here without actual normalization, the filter code
is in device units as of bdd4264d61.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
These conditions were never triggered by our test suite, so let's tighten up
the tests to match what we expect.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
The first event is always a device added event, skip the loops that would
paper over this. If we ever change this, the tests *should* fail.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
The second condition was never triggered because we shouldn't get anything but
keyboard events here. Drain the initial event burst and remove the two
skipping conditions that won't happen anyway.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
From systemd commit f644a6da7a: "pyparsing 2.1.10 fixed the handling of
LineStart to really just apply to line starts and not ignore whitespace and
comments any more. Adjust EMPTYLINE to this."
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
I'm using semaphore CI for build testing and that only provides Ubuntu 14.04
which doesn't have libevdev 1.3 or later.
Since this is a minor workaround for an error case only, revert the commit
again and leave the handling in. Less effort than having to patch around it in
semaphore.
This reverts commit 1e0736daf3.
gcov analysis showed that none of the actual testing conditions were hit, so
the test succeeded despite not actually testing anything. Which is good,
because testing for tilt normalization isn't correct anyway, tilt is in
physical degrees,
Drop the test and replace it with a test for pressure normalization instead.
We already have a similar one to check for [0, 1] range, this new one
explicitly tests for the extents.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
They weren't originally prefixed but the various tests were, but now that we
only have one test runner binary anyway, the prefix helps sorting the files
easily within e.g. gcov results.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Use the litest_assert_empty_queue() instead of manual checking, and remove the
manual checks after the function call.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
These were just there so we didn't have an unused variable warning, but
there's no reason even assigning to anything in the first place
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
We used to mark dell touchpads this way but let's make this more generic.
Nothing else used the dell touchpad model flag, so we can simply replace it.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
This is added on top of the click angle handling, so the actual axis values
simply fall back onto whatever is set by udev, including the default fallbacks
to 15 and whatnot.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Only allow values of 0 and 1 for udev flags. Not that I'm aware of anyone
using anything else (i.e. his shouldn't break anything) but it's best to be as
restrictive as possible here.
Bonus effect: it's now possible to unset LIBINPUT_MODEL_* tags as well,
previously any value (including 0) was counted as "yes".
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
If the fingers rest on the touchpad without moving for a timeout, switch to
pinch or swipe based on the finger position. We already switched to two-finger
scrolling based on the timeout, now we also do so for 3 and 4 finger gestures.
This gives us better reaction to small movements.
This also fixes previously unreachable code: the test for the finger position
required at least 3 fingers down but was within a condition that ensured only
2 fingers were down. This was introduced in 11917061fe.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
