libinput/doc/tablet-support.dox

/**
@page tablet-support Tablet support

This page provides details about the graphics tablet
support in libinput. Note that the term "tablet" in libinput refers to
graphics tablets only (e.g. Wacom Intuos), not to tablet devices like the
Apple iPad.

@image html tablet.svg "Illustration of a graphics tablet"

@section tablet-tools Pad buttons vs. tablet tools

Most tablets provide two types of devices. The physical tablet often
provides a number of buttons and a touch ring or strip. Interaction on the
drawing surface of the tablet requires a tool, usually in the shape of a
stylus.  The libinput interface exposed by devices with the @ref
LIBINPUT_DEVICE_CAP_TABLET_TOOL capability applies only to events generated
by tools.

Buttons, rings or strips on the physical tablet hardware (the "pad") are
exposed by devices with the @ref LIBINPUT_DEVICE_CAP_TABLET_PAD capability.
Pad events do not require a tool to be in proximity. Note that both
capabilities may exist on the same device though usually they are split
across multiple kernel devices.

Touch events on the tablet integrated into a screen itself are exposed
through the @ref LIBINPUT_DEVICE_CAP_TOUCH capability. Touch events on a
standalone tablet are exposed through the @ref LIBINPUT_DEVICE_CAP_POINTER
capability.  In both cases, the kernel usually provides a separate event
node for the touch device, resulting in a separate libinput device.
See libinput_device_get_device_group() for information on how to associate
the touch part with other devices exposed by the same physical hardware.

@section tablet-tip Tool tip events vs. tool button events

The primary use of a tablet tool is to draw on the surface of the tablet.
When the tool tip comes into contact with the surface, libinput sends an
event of type @ref LIBINPUT_EVENT_TABLET_TOOL_TIP, and again when the tip
ceases contact with the surface.

Tablet tools may send button events; these are exclusively for extra buttons
unrelated to the tip. A button event is independent of the tip and can while
the tip is down or up.

Some tablet tools' pressure detection is too sensitive, causing phantom
touches when the user only slightly brushes the surfaces. For example, some
tools are capable of detecting 1 gram of pressure.

libinput uses a device-specific pressure threshold to determine when the tip
is considered logically down. As a result, libinput may send a nonzero
pressure value while the tip is logically up. Most application can and
should ignore pressure information until they receive the event of type @ref
LIBINPUT_EVENT_TABLET_TOOL_TIP. Applications that require extremely
fine-grained pressure sensitivity should use the pressure data instead of
the tip events to determine a logical tip down state and treat the tip
events like axis events otherwise.

Note that the pressure threshold to trigger a logical tip event may be zero
on some devices. On tools without pressure sensitivity, determining when a
tip is down is device-specific.

@section tablet-relative-motion Relative motion for tablet tools

libinput calculates the relative motion vector for each event and converts
it to the same coordinate space that a normal mouse device would use. For
the caller, this means that the delta coordinates returned by
libinput_event_tablet_tool_get_dx() and
libinput_event_tablet_tool_get_dy() can be used identical to the delta
coordinates from any other pointer event. Any resolution differences between
the x and y axes are accommodated for, a delta of N/N represents a 45 degree
diagonal move on the tablet.

The delta coordinates are available for all tablet events, it is up to the
caller to decide when a tool should be used in relative mode. It is
recommended that mouse and lens cursor tool default to relative mode and
all pen-like tools to absolute mode.

If a tool in relative mode must not use pointer acceleration, callers
should use the absolute coordinates returned by
libinput_event_tablet_tool_get_x() and libinput_event_tablet_tool_get_y()
and calculate the delta themselves. Callers that require exact physical
distance should also use these functions to calculate delta movements.

@section tablet-axes Special axes on tablet tools

A tablet tool usually provides additional information beyond x/y positional
information and the tip state. A tool may provide the distance to the tablet
surface and the pressure exerted on the tip when in contact. Some tablets
additionally provide tilt information along the x and y axis.

@image html tablet-axes.svg "Illustration of the distance, pressure and tilt axes"

The granularity and precision of the distance and pressure axes varies
between tablet devices and cannot usually be mapped into a physical unit.
libinput normalizes distance and pressure into the [0, 1] range.

While the normalization range is identical for these axes, a caller should
not interpret identical values as identical across axes, i.e. a value v1 on
the distance axis has no relation to the same value v1 on the pressure axis.

The tilt axes provide the angle in degrees between a vertical line out of
the tablet and the top of the stylus. The angle is measured along the x and
y axis, respectively, a positive tilt angle thus means that the stylus' top
is tilted towards the logical right and/or bottom of the tablet.

@section tablet-fake-proximity Handling of proximity events

libinput's @ref LIBINPUT_EVENT_TABLET_TOOL_PROXIMITY events notify a caller
when a tool comes into sensor range or leaves the sensor range. On some
tools this range does not represent the physical range but a reduced
tool-specific logical range. If the range is reduced, this is done
transparent to the caller.

For example, the Wacom mouse and lens cursor tools are usually
used in relative mode, lying flat on the tablet. Movement typically follows
the interaction normal mouse movements have, i.e. slightly lift the tool and
place it in a separate location. The proximity detection on Wacom
tablets however extends further than the user may lift the mouse, i.e. the
tool may not be lifted out of physical proximity. For such tools, libinput 
provides software-emulated proximity. 

Events from the pad do not require proximity, they may be sent any time.

@section tablet-pressure-offset Pressure offset on worn-out tools

When a tool is used for an extended period it can wear down physically. A
worn-down tool may never return a zero pressure value. Even when hovering
above the surface, the pressure value returned by the tool is nonzero,
creating a fake surface touch and making interaction with the tablet less
predictable.

libinput automatically detects pressure offsets and rescales the remaining
pressure range into the available range, making pressure-offsets transparent
to the caller. A tool with a pressure offset will thus send a 0 pressure
value for the detected offset and nonzero pressure values for values higher
than that offset.

Some limitations apply to avoid misdetection of pressure offsets,
specifically:
- pressure offset is only detected on proximity in, and if a device is
  capable of detection distances,
- pressure offset is only detected if the distance between the tool and the
  tablet is high enough,
- pressure offset is only used if it is 20% or less of the pressure range
  available to the tool. A pressure offset higher than 20% indicates either
  a misdetection or a tool that should be replaced, and
- if a pressure value less than the current pressure offset is seen, the
  offset resets to that value.

Pressure offsets are not detected on @ref LIBINPUT_TABLET_TOOL_TYPE_MOUSE
and @ref LIBINPUT_TABLET_TOOL_TYPE_LENS tools.

@section tablet-serial-numbers Tracking unique tools

Some tools provide hardware information that enables libinput to uniquely
identify the physical device. For example, tools compatible with the Wacom
Intuos 4, Intuos 5, Intuos Pro and Cintiq series are uniquely identifiable
through a serial number. libinput does not specify how a tool can be
identified uniquely, a caller should use libinput_tablet_tool_is_unique() to
check if the tool is unique.

libinput creates a struct libinput_tablet_tool on the first proximity in of
this tool. By default, this struct is destroyed on proximity out and
re-initialized on the next proximity in. If a caller keeps a reference to
the tool by using libinput_tablet_tool_ref() libinput re-uses this struct
whenever that same physical tool comes into proximity on any tablet
recognized by libinput. It is possible to attach tool-specific virtual state
to the tool. For example, a graphics program such as the GIMP may assign a
specific color to each tool, allowing the artist to use the tools like
physical pens of different color. In multi-tablet setups it is also
possible to track the tool across devices.

If the tool does not have a unique identifier, libinput creates a single
struct libinput_tablet_tool per tool type on each tablet the tool is used
on.

@section tablet-tool-types Vendor-specific tablet tool types

libinput supports a number of high-level tool types that describe the
general interaction expected with the tool. For example, a user would expect
a tool of type @ref LIBINPUT_TABLET_TOOL_TYPE_PEN to interact with a
graphics application taking pressure and tilt into account. The default
virtual tool assigned should be a drawing tool, e.g. a virtual pen or brush.
A tool of type @ref LIBINPUT_TABLET_TOOL_TYPE_ERASER would normally be
mapped to an eraser-like virtual tool. See @ref libinput_tablet_tool_type
for the list of all available tools.

Vendors may provide more fine-grained information about the tool in use by
adding a hardware-specific tool ID. libinput provides this ID to the caller
with libinput_tablet_tool_get_tool_id() but makes no promises about the
content or format of the ID.

libinput currently supports Wacom-style tool IDs as provided on the Wacom
Intuos 3, 4, 5, Wacon Cintiq and Wacom Intuos Pro series. The tool ID can
be used to distinguish between e.g. a Wacom Classic Pen or a Wacom Pro Pen.
It is  the caller's responsibility to interpret the tool ID.

@section tablet-bounds Out-of-bounds motion events

Some tablets integrated into a screen (e.g. Wacom Cintiq 24HD, 27QHD and
13HD series, etc.) have a sensor larger than the display area. libinput uses
the range advertised by the kernel as the valid range unless device-specific
quirks are present. Events outside this range will produce coordinates that
may be negative or larger than the tablet's width and/or height. It is up to
the caller to ignore these events.

@image html tablet-out-of-bounds.svg "Illustration of the out-of-bounds area on a tablet"

In the image above, the display area is shown in black. The red area around
the display illustrates the sensor area that generates input events. Events
within this area will have negative coordinate or coordinates larger than
the width/height of the tablet.

If events outside the logical bounds of the input area are scaled into a
custom range with libinput_event_tablet_tool_get_x_transformed() and
libinput_event_tablet_tool_get_y_transformed() the resulting value may be
less than 0 or larger than the upper range provided. It is up to the caller
to test for this and handle or ignore these events accordingly.

@section tablet-pad-buttons Tablet pad button numbers

Tablet Pad buttons are numbered sequentially, starting with button 0. Thus
button numbers returned by libinput_event_tablet_pad_get_button_number()
have no semantic meaning, a notable difference to the button codes returned
by other libinput interfaces (e.g. libinput_event_tablet_tool_get_button()).

The Linux kernel requires all input events to have semantic event codes,
but generic buttons like those on a pad cannot easily be assigned semantic
codes. The kernel supports generic codes in the form of BTN_0 through to
BTN_9 and additional unnamed space up until code 0x10f. Additional generic
buttons are available as BTN_A in the range dedicated for gamepads and
joysticks. Thus, tablet with a large number of buttons have to map across
two semantic ranges, have to use unnamed kernel button codes or risk leaking
into an unrelated range. libinput transparently maps the kernel event codes
into a sequential button range on the pad. Callers should use external
sources like libwacom to associate button numbers to their position on the
tablet.

Some buttons may have expected default behaviors. For example, on Wacom
Intuos Pro series tablets, the button inside the touch ring is expected to
switch between a mode switch. Mode switching is a feature implemented in the
caller and libinput does not provide specific handling. Callers should use
external sources like libwacom to identify which buttons have semantic
behaviors.

*/