Meson has shared_library and shared_module. The latter should be used
only for shared plugins loaded by dlopen, not for shared libraries
linked by the linker.
The target `nm_wwan` was defined as shared_module probably because it
is a library for loadable plugins only, andcontains references to
symbols from the main executable that cannot be resolved at link time.
Do as the deprecation message suggest and convert it to shared_library
with b_lundef=false:
DEPRECATION: target nm-device-plugin-wwan links against shared module nm-wwan, which is incorrect.
This will be an error in the future, so please use shared_library() for nm-wwan instead.
If shared_module() was used for nm-wwan because it has references to undefined symbols,
use shared_library() with `override_options: ['b_lundef=false']` instead.
When IPv6 privacy extensions are enabled, by default temporary addresses
have a valid lifetime of 1 week and a preferred lifetime of 1 day.
That's far too long for privacy-conscious users, some of whom want a new
address once every few seconds. Add connection options that correspond
to /proc/sys/net/ipv6/conf/*/temp_valid_lft and
/proc/sys/net/ipv6/conf/*/temp_prefered_lft to allow configuring the
address rotation time on a per-connection basis.
The new properties are defined as 32-bit signed integers to match the
sysctl parameters which are also signed, although currently only
positive numbers are valid.
A common source for doubts and questions from users is about why
devices are unmanaged. Unfortunately NM doesn't expose that
information properly via D-Bus and so it's not available in nmcli.
The device D-Bus object has two properties that are strictly related:
"state" and "state-reason". The latter represents the reason for the
current state. Introduce new reasons to indicate the possible causes
for the unmanaged state. Note that a device can be unmanaged because
of multiple reasons at the same time, we only return one.
Before:
$ nmcli -f GENERAL.DEVICE,GENERAL.TYPE,GENERAL.STATE,GENERAL.reason device show
GENERAL.DEVICE: enp7s0
GENERAL.TYPE: ethernet
GENERAL.STATE: 10 (unmanaged)
GENERAL.REASON: 0 (No reason given)
GENERAL.DEVICE: tun0
GENERAL.TYPE: tun
GENERAL.STATE: 10 (unmanaged)
GENERAL.REASON: 0 (No reason given)
GENERAL.DEVICE: hwsim0
GENERAL.TYPE: unknown
GENERAL.STATE: 10 (unmanaged)
GENERAL.REASON: 0 (No reason given)
After:
$ nmcli -f GENERAL.DEVICE,GENERAL.TYPE,GENERAL.STATE,GENERAL.reason device show
GENERAL.DEVICE: enp7s0
GENERAL.TYPE: ethernet
GENERAL.STATE: 10 (unmanaged)
GENERAL.REASON: 76 (The device is unmanaged by user decision via settings plugin ("unmanaged-devices" for keyfile or "NM_CONTROLLED=no" for ifcfg-rh))
GENERAL.DEVICE: tun0
GENERAL.TYPE: tun
GENERAL.STATE: 10 (unmanaged)
GENERAL.REASON: 75 (The device is unmanaged by explicit user decision (e.g. 'nmcli device set $DEV managed no')
GENERAL.DEVICE: hwsim0
GENERAL.TYPE: unknown
GENERAL.STATE: 10 (unmanaged)
GENERAL.REASON: 69 (The device is unmanaged because the device type is unmanaged by default)
https://gitlab.freedesktop.org/NetworkManager/NetworkManager/-/merge_requests/1887
When creating VLAN over OVS internal interface which holding the same
name as its controller OVS bridge, NetworkManager will fail with error:
Error: Connection activation failed: br0.101 failed to create
resources: cannot retrieve ifindex of interface br0 (Open vSwitch
Bridge)
Expanded the `find_device_by_iface()` with additional argument
`child: NmConnection *` which will validate whether candidate is
suitable to be parent device.
In `nm_device_check_parent_connection_compatible()`, we only not allow OVS
bridge and OVS port being parent.
Resolves: https://issues.redhat.com/browse/RHEL-26753
Signed-off-by: Gris Ge <fge@redhat.com>
Introduce a new option to NMSettingIpConfig. The new option is ternary
type being the default value set to disabled. When enabled,
NetworkManager will instruct the DHCP client to send RELEASE message
when IP addresses are being removed.
The argument might imply that when set to FALSE, the dhcp client won't
send a RELEASE message. This won't be true with the new
dhcp-send-release option that is going to be introduced.
Instead, change the name to "force_release", when set to TRUE it means
we are sending a RELEASE message even if not indicated by the user. When
set to FALSE, it will be up to the user.
When a generic connection has a custom device-handler, it always
generates a NMDeviceGeneric, even when the link that gets created is
of a type natively supported by NM. On service restart, we need to
keep track that the device is generic or otherwise a different device
type will be instantiated.
(cherry picked from commit f2613be150)
If the device-handler of the generic connection is set, the connection
is virtual and the device is created by invoking the device-handler
via NetworkManager-dispatcher service.
With this change, a generic device now represents two different device
classes:
- existing interfaces that are not natively supported or recognized
by NetworkManager. Those devices have the `has_device_handler`
property set to FALSE;
- interfaces that are created by NM by invoking the device-handler;
they have `has_device_handler` set to TRUE.
(cherry picked from commit df6c35ec75)
Set these parameters according to the values set in the new properties
sriov.eswitch-inline-mode and sriov.eswitch-encap-mode.
The number of parameters related to SR-IOV was becoming too big.
Refactor to group them in a NMPlatformSriovParams struct and pass it
around.
(cherry picked from commit 4669f01eb0)
When the lease is lost, NM tries to get a new by restarting the DHCP
transaction. However, it doesn't delete the existing l3cds (one from
the DHCP client with flag ONLY_FOR_ACD, the other from
NMDevice). Therefore, the l3cfg still tracks the ACD state of the
address as "external-removed", and when NM gets the same address via
DHCP, ACD is considered as failed; as a consequence, NM sends a
DECLINE message to the server.
Moreover, the l3cd added by NMDevice for DHCP has a zero ACD timeout,
and so it's not possible to do ACD again on the same address.
Remove those l3cds when the lease expires, so that any ACD state is
cleared and DHCP can perform ACD again.
Fixes: 240ec7f891 ('dhcp: implement ACD (address collision detection) for DHCPv4')
https://gitlab.freedesktop.org/NetworkManager/NetworkManager/-/merge_requests/1853
(cherry picked from commit a80fef9f37)
When doing reapply on linux bridge interface, NetworkManager will reset
the VLAN filtering and default PVID which cause PVID been readded to all
bridge ports regardless they are managed by NetworkManager.
This is because Linux kernel will re-add PVID to bridge port upon the
changes of bridge default-pvid value.
To fix the issue, this patch introduce netlink parsing code for
`vlan_filtering` and `default_pvid` of NMPlatformLnkBridge, and use that
to compare desired VLAN filtering settings, skip the reset of VLAN
filter if `default_pvid` and `vlan_filtering` are unchanged.
Signed-off-by: Gris Ge <fge@redhat.com>
(cherry picked from commit 02c34d538c)
Mark the methods/properties deprecated in the D-Bus API (via
org.freedesktop.DBus.Introspectable.Introspect(), [1]).
It affects those properties that are documented as deprecated in
introspection XML.
$ busctl -j call \
org.freedesktop.NetworkManager \
/org/freedesktop/NetworkManager \
org.freedesktop.DBus.Introspectable \
Introspect | \
jq '.data[0]' -r | \
grep -5 Deprecated
[1] https://dbus.freedesktop.org/doc/dbus-specification.html#standard-interfaces-introspectable
A IPv4 conflict detected during the probe is a serious problem, as it
prevents the address from being configured. As such, is should be
displayed at warning level.
A conflict detected after the address is already configured
(addr_info->state == NM_L3_ACD_ADDR_STATE_CONFLICT) is less important
because NM will try to defend the address and will keep using it.
A duplicate address is a serious issue which leads to non-working
setups or problems hard to debug. Enable IPv4 duplicate address
detection (aka ACD, RFC 5227) by default to detect such problems.
While the RFC recommends a timeout of 9 seconds, a comment in n-acd
sources says:
A 9s timeout for successful link setups is not acceptable today.
Hence, we will just go forward and ignore the proposed values. On
both wired and wireless local links round-trip latencies of below
3ms are common. We require the caller to set a timeout multiplier,
where 1 corresponds to a total probe time between 0.5 ms and 1.0
ms. On modern networks a multiplier of about 100 should be a
reasonable default. To comply with the RFC select a multiplier of
9000.
Set a default timeout of 200ms, which is the double of the value
suggested in n-acd sources. 200ms sounds quick enough, and gives at
least ~100ms to other hosts to reply.
See also the Fedora change proposal:
https://fedoraproject.org/wiki/Changes/Enable_IPv4_Address_Conflict_Detection
The supervision address is read-only. It is constructed by kernel and
only the last byte can be modified by setting the multicast-spec as
documented indeed.
As 1.46 was not released yet, we still can drop the whole API for this
setting property. We are keeping the NMDeviceHsr property as it is a
nice to have for reading it.
https://gitlab.freedesktop.org/NetworkManager/NetworkManager/-/merge_requests/1823
Fixes: 5426bdf4a1 ('HSR: add support to HSR/PRP interface')
Setting
wifi.cloned-mac-address="stable-ssid"
should generate the same SSID as
connection.stable-id="${NETWORK_SSID}"
wifi.cloned-mac-address="stable"
For that to work correctly, we need to post-process the generated stable
id.
Fixes: d210923c0f ('wifi: add "wifi.cloned-mac-address=stable-ssid"')
https://gitlab.freedesktop.org/NetworkManager/NetworkManager/-/merge_requests/1813
"nm-glib" h contains compat wrappers for older glib versions. This file
used to be copied over to VPN plugins, to use the same compat code. It
was thus interesting to also have compat code for glib versions, that
were no longer supported by NetworkManager itself.
This was fine. But glib 2.42 is more than 8 years old. At this point,
there really is no need to support that, even if you copy the file out
of NetworkManager source tree.
Drop those compat wrappers.
This patch add support to HSR/PRP interface. Please notice that PRP
driver is represented as HSR too. They are different drivers but on
kernel they are integrated together.
HSR/PRP is a network protocol standard for Ethernet that provides
seamless failover against failure of any network component. It intends
to be transparent to the application. These protocols are useful for
applications that request high availability and short switchover time
e.g electrical substation or high power inverters.
https://gitlab.freedesktop.org/NetworkManager/NetworkManager/-/merge_requests/1791
Users should not be allowed to start or stop a wifi-p2p scan unless
they have some kind of permission. Since we already have the
"org.freedesktop.NetworkManager.wifi.scan" permission for wifi scans,
check that.
Fixes: dd0c59c468 ('core/devices: Add DBus methods to start/stop a P2P find')
https://gitlab.freedesktop.org/NetworkManager/NetworkManager/-/merge_requests/1795
When connection down is explicitly called on the controller, the port
connection should also be deactivated with the reason user-requested,
otherwise any following connection update on the controller profile
will unblock the port connection and unnessarily make the port to
autoconnet again.
Fixes: 645a1bb0ef ('core: unblock autoconnect when master profile changes')
https://gitlab.freedesktop.org/NetworkManager/NetworkManager-ci/-/merge_requests/1568
Add a new "stable-ssid" mode that generates the MAC address based on the
Wi-Fi's SSID.
Note that this gives the same MAC address as setting
connection.stable-id="${NETWORK_SSID}"
wifi.cloned-mac-address="stable"
The difference is that changing the stable ID of a profile also affects
"ipv6.addr-gen-mode=stable-privacy" and other settings.
For Wi-Fi profiles, this will encode the SSID in the stable-id.
For other profiles, this encodes the connection UUID (but the SSID and
the UUID will always result in distinct stable IDs).
Also escape the SSID, so that the generated stable-id is always valid
UTF-8.
Comparing integers of different signedness gives often unexpected
results. Adjust usages of MIN()/MAX() to ensure that the arguments agree
in signedness.
Some Applications require to explicitly enable or disable EEE.
Therefore introduce EEE (Energy Efficient Ethernet) support with:
* ethtool.eee on/off
Unit test case included.
Signed-off-by: Johannes Zink <j.zink@pengutronix.de>
When creating default connections automatically, we check if udev has
set the NM_AUTO_DEFAULT_LINK_LOCAL_ONLY variable, and if so, we create
the connection with method=link-local. It was checked only for ethernet
connection type, which works fine because it's the only device type that
we create connections automatically for.
However, link-local connections are not specific to Ethernet, and if we
add auto-default connections for more devices in the future we should
honor this configuration too. Do it from nm-device, but only if the
device class has defined a "new_default_connection" method so the
behaviour is identical as the current one, but will be used by future
implementors of this method too.
See-also: https://gitlab.freedesktop.org/NetworkManager/NetworkManager/-/merge_requests/1780https://gitlab.freedesktop.org/NetworkManager/NetworkManager/-/merge_requests/1779
We honored "NM_AUTO_DEFAULT_LINK_LOCAL_ONLY" udev property, for when we
generate a "Wired connection 1" (aka the "auto-default connection").
Systemd now also honors and may set ID_NET_AUTO_LINK_LOCAL_ONLY for
a similar purpose. Honore that too.
The NM specific variable still is preferred, also because "NM_AUTO_DEFAULT_LINK_LOCAL_ONLY"
is about something very NetworkManager specific (controlling "Wired connection 1").
Maybe one day, we should drop "data/90-nm-thunderbolt.rules" and only
rely on what systemd provides. But not yet.
See-also: https://github.com/systemd/systemd/pull/29767https://gitlab.freedesktop.org/NetworkManager/NetworkManager/-/issues/1413
If a ovs interface has the cloned-mac-address property set, we pass
the desired MAC to ovsdb when creating the db entry, and openvswitch
will eventually assign it to the interface.
Note that usually the link will not have the desired MAC when it's
created. Therefore, currently we also change the MAC via netlink
before proceeding with IP configuration. This is important to make
sure that ARP announcements, DHCP client-id, etc. will use the correct
MAC address.
This doesn't work when using the "netdev" (userspace) datapath, as the
attempts to change the MAC of the tun interface via netlink fail,
leading to an activation failure.
To properly handle both cases in the same way, adopt a different
strategy: now we don't set the MAC address explicitly via netlink but
we only wait until ovs does that.
