Rather than randomly including one or more of <glib.h>,
<glib-object.h>, and <gio/gio.h> everywhere (and forgetting to include
"nm-glib-compat.h" most of the time), rename nm-glib-compat.h to
nm-glib.h, include <gio/gio.h> from there, and then change all .c
files in NM to include "nm-glib.h" rather than including the glib
headers directly.
(Public headers files still have to include the real glib headers,
since nm-glib.h isn't installed...)
Also, remove glib includes from header files that are already
including a base object header file (which must itself already include
the glib headers).
A number of classes in core had their own error domains that aren't
really necessary.
In the case of NMDcbError, NMDhcpManagerError, NMDnsManagerError,
NMDnsmasqManagerError, NMPppManagerError, and NMSessionMonitorError,
most of the codes they defined weren't even being used, and at any
rate, the errors were always returned into contexts where they would
just have their message extracted and then get thrown away without
anyone ever looking at the domain or code. So all uses of those
domains can just be replaced with NM_MANAGER_ERROR_FAILED without any
loss of information.
NMAuthManagerError only had 1 error code, and it just indicated
"something went wrong", so it can be replaced with
NM_MANAGER_ERROR_FAILED without loss of information.
(nm-auth-manager.c has also been fixed to return
NM_MANAGER_ERROR_FAILED when the CheckAuthorization D-Bus call fails,
rather than returning whatever error domain/code the D-Bus call
returned.)
NMVpnManagerError used 2 of its 4 error codes, and they could actually
end up getting returned across D-Bus in some cases. But there are
NMManagerError codes that are semantically similar enough to make the
NMVpnManagerError ones unnecessary.
Previously, src/nm-ip4-config.h, libnm/nm-ip4-config.h, and
libnm-glib/nm-ip4-config.h all used "NM_IP4_CONFIG_H" as an include
guard, which meant that nm-test-utils.h could not tell which of them
was being included (and so, eg, if you tried to include
nm-ip4-config.h in a libnm test, it would fail to compile because
nm-test-utils.h was referring to symbols in src/nm-ip4-config.h).
Fix this by changing the include guards in the non-API-stable parts of
the tree:
- libnm-glib/nm-ip4-config.h remains NM_IP4_CONFIG_H
- libnm/nm-ip4-config.h now uses __NM_IP4_CONFIG_H__
- src/nm-ip4-config.h now uses __NETWORKMANAGER_IP4_CONFIG_H__
And likewise for all other headers.
The two non-"nm"-prefixed headers, libnm/NetworkManager.h and
src/NetworkManagerUtils.h are now __NETWORKMANAGER_H__ and
__NETWORKMANAGER_UTILS_H__ respectively, which, while not entirely
consistent with the general scheme, do still mostly make sense in
isolation.
Non-git-master versions of lldpad refuse to touch a device that doesn't
have a carrier. And when enabling/disabling DCB, the kernel driver will
reconfigure itself and may turn carrier off for a few seconds. So we
must ensure that before enabling/disabling DCB, the carrier is already
on. Next we must ensure that *after* enabling/disabling DCB, the
carrier is back on before doing further DCB setup.
There's a race condition between enabling/disabling DCB and receiving
the carrier event in NetworkManager that has to be handled carefully.
Because the carrier may not yet be down after the dcbtool call to
enable/disable DCB returns, we need to wait for a couple seconds for
the carrier to go down, and then again for it to come back up.
Otherwise we might see the still-on carrier, proceed with DCB setup,
and the carrier finally goes down halfway through the setup, which
will fail the operations with "DCB not enabled, link down, or DCB
not supported" errors from lldpad.
